Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,
including the following:
Children should be supervised to ensure that they do not
play with the appliance.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
Do not use an extension cord.
If power supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or a similarly qualified
person in order to avoid a hazard.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Unpack the Ice Maker
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
Removing Packaging Materials
Remove tape and glue from your ice maker before using.
To remove any remaining tape or glue from the exterior of the
■
ice maker, rub the area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with your
fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
■
fluids, or abrasive cleaners to remove tape or glue. Do not
use chlorine bleach on the stainless steel surfaces of the ice
maker. These products can damage the surface of your ice
maker.
Cleaning Before Use
After you remove all of the packaging materials, clean the inside
of your ice maker before using it. See the cleaning instructions in
the "Ice Maker Care" section of Use and Care Guide.
Vacation or Extended Time Without Use
When you will not be using the ice maker for an extended
■
period of time, turn off the water and power supply to the ice
maker.
Check that the water supply lines are insulated against
■
freezing conditions. Ice formations in the supply lines can
increase water pressure and cause damage to your ice
maker or home. Damage from freezing is not covered by the
warranty.
2
Connect to potable water supply only.
This appliance is intended to be used in household and
similar applications such as: staff kitchen areas in shops,
offices, and other working environments; farm houses and
by clients in hotels, motels, and other residential-type
environments; bed and breakfast-type environments; and
catering and similar non-retail applications.
Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
Do not use replacement parts that have not been
recommended by the manufacturer (e.g., parts made at
home using a 3D printer).
Location Requirements
Installation must comply with all governing codes and
■
ordinances.
To ensure proper ventilation for your ice maker, the front
■
side must be completely unobstructed. The ice maker may
be closed-in on the top and three sides, but the installation
should allow the ice maker to be pulled forward for servicing if
necessary.
The auxiliary grill kit provided (only on custom panel models)
■
can be used to align the toe grill with the rest of the cabinets
while not obstructing ventilation of the ice maker.
Installation of the ice maker requires a cold water supply inlet
■
of 1/4" (6.35 mm) OD soft copper tubing with a shutoff valve
or a Whirlpool supply line Part Number 8212547RB, and a
Whirlpool approved drain pump, Part Number 1901A, only to
carry the water to an existing drain.
Choose a well-ventilated area with temperatures above 55°F
■
(13°C) and below 110°F (43°C). Best results are obtained
between 70°F and 90°F (21ºC and 32°C).
The ice maker must be installed in an area sheltered from the
■
elements, such as wind, rain, water spray, or drip.
When installing the ice maker under a counter, follow the
■
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as shown.
NOTES:
Check that the power supply cord is not damaged or
■
pinched or kinked between the ice maker and the cabinet.
Check that the water supply line is not damaged or
■
pinched or kinked between the ice maker and the cabinet.
Check that the drain line (on some models) is not
■
damaged or pinched or kinked between the ice maker and
the cabinet.
Choose a location where the floor is even. It is important for
■
the ice maker to be level in order to work properly. If needed,
you can adjust the height of the ice maker by changing the
height of the leveling legs. See "Leveling and Securing."
Model Identification:
Standard model
Custom panel model
Standard Model Utilities
11¹⁄
"
2
(29.2 cm)
34"
(86.4 cm)
Min.
28¹⁄
"
34¹⁄
"
2
2
(72.4 cm)
(87.6 cm)
Max.
9"
3¹⁄
"
2
(22.9 cm)
(8.9 cm)
24"
(60.96 cm)
A. Recommended location for electrical and plumbing fixtures
B. Floor level
Custom Panel Model Utilities
Required zone
for utility hole/slot
cutout location
A
B
C
D
71/2"
71/2"
(19.05 cm)
(19.05 cm)
Utility Slot/Cutout Location Zone
A
9" (22.9 cm)
Dimension
B
8" (20.3 cm)
C
7" (17.8 cm)
Diameter of the hole
D
2" (5 cm)
Custom Panel ice maker models have been designed for flush
■
install in instances where the power supply, water supply, and
drain are located in adjacent cabinetry.
For installation of product with utilities behind the ice maker,
■
flush install may not be achieved.
Refer "Custom Panel Model Utilities" illustration and table
■
below it for utility slot/hole cutout location.
Electrical Requirements
WARNING
Electrical Shock Hazard
A
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
B
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical connection:
A 115 V, 60 Hz, AC only, 15 A or 20 A electrical supply, properly
grounded in accordance with the National Electrical Code and
local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
IMPORTANT: If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) equipped outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Ice quality
may be affected. If nuisance tripping has occurred, and if the
condition of the ice appears poor, dispose of it.
Recommended Grounding Method
The ice maker must be grounded. The ice maker is equipped with
a power supply cord having a 3 prong grounding plug. The cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall receptacle
is not available, it is the personal responsibility of the customer to
have a properly grounded, 3 prong wall receptacle installed by a
qualified electrician.
3
Publicité
Table des Matières
