Table des Matières
Publicité
Item
Dia.
No.
Mkgs.
. . .
10
. . . . . . . . . . . . . . . .
. . .
11
. . . . . . . . . . . . . . . .
. . .
12
. . . . . . . . . . . . . . . .
. . .
13
. . . . . . . . . . . . . . . .
. . .
14
. . . . . . . . . . . . . . . .
. . .
15
. . . . . . . . . . . . . . . .
. . .
16
. . . . . . . . . . . . . . . .
. . .
17
. . . . . . . . . . . . . . . .
. . .
18
. . . . . . . . . . . . . . . .
. . .
19
. . . . . . . . . . . . . . . .
. . .
20
. . . . . . . . . . . . . . . .
. . .
21
. . . . . . . . . . . . . . . .
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer's Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
Ordering Information For PCM, AIM And UIM Circuit Boards
The UIM, AIM and PCM boards must have compatible programs in order to communicate together and provide proper system performance. If the
program has been updated since the system was received, the original program revision may not match the serial number of the PipePro 300 shown in
Table 9-1. In order to provide the correct replacement board, it is necessary to know the program revision for each of the boards in the PipePro 300.
Follow the procedure to Check Program Revision for each board according to Section 5-15.
The last three numbers of the program and the program revision letter appear on the display. All three boards will match one of the rows horizontally in
Table 9-1. The WFCM board will appear on the display for earlier versions of program. This board is not used in the PipePro 300 so it can be ignored in
this case. Once the board program revisions are identified, use Table 9-1 to select the proper replacement board part number(s).
If the program revision cannot be found due to board failure, the serial number and/or knowledge of a prior update must be used to determine the correct
board number. Another welding power source at the same location may be used to determine the program revision to remain consistent.
UIM
Stock Number
907489
Software
Board
226429D
246895
226429E
247937
Part
No.
Figure 10-5. Front Panel Assembly (Fig 10-1 Item 14) (Continued)
216966
. . .
Cover, Connector D-sub 9 pin Male w/Chain
213102
. . .
Choke, Common Mode w/Leads
210866
. . .
Terminal, pwr output black
210476
. . .
Panel, Front
219843
. . .
Label, Volt Sense
207979
. . .
Box, Louver
186621
. . .
Boot, Generic
231056
. . .
Knob,Black Electroswitch
212779
. . .
Nameplate, Front
210865
. . .
Terminal, pwr output red
210483
. . .
Bracket, lift eye
210358
. . .
Bolt, eye shld thd stem .500−13 X 1.500
Table 9-1. Program Revisions For Circuit Boards
907435
Board
Software
249383
226431B
249384
226431B
Description
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIM
Board
Software
238019
222230H
238019
222230J
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
PCM
Original
Manufacture
Starting
w/Serial No.
Board
246554
LK310043G
247935
MA120110G
OM-243 915 Page 69
Quantity
1
2
1
1
1
1
2
1
1
1
1
1
Publicité
Table des Matières
