Intended Use; Technical Data; Assembly - EINHELL BG-CB 2041 T Mode D'emploi D'origine

3. Intended use

The pole-mounted petrol-powered pruner is
designed for lopping off tree branches. It is not
suitable for extensive sawing work, felling trees or
sawing any materials other than wood.
The equipment may be used only for its intended
purpose. Any other use is deemed to be a case
of misuse.
The user/operator and not the manufacturer will
be liable for any damage or injuries of any kind
which result from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.

4. Technical data

Engine type .................................2-stroke engine,
.................................. air-cooled, chrome cylinder
Engine output (max.).....................0.8 kW / 1.1 hp
Displacement .........................................25.4 cm3
Idle engine speed ...............................3,200 min
Max. engine speed..............................8,500 min
Cutter bar length ............................... 8" (200 mm)
Max. cutting length .................................. 180 mm
Chain pitch .................................. 9.525 mm (3/8")
Chain thickness ..................................... 1.27 mm
Chain wheel teeth ...................7 teeth / 9.525 mm
Cutting speed at rated rpm ........................18 m/s
Oil tank capacity ........................................120 ml
Weight without cutter bar and chain ............5.9 kg
Chain ........................................Oregon 91P033X
Cutter bar ...........................Oregon 080SDEA318
Ignition ..................................................Electronic
Drive .........................................Centrifugal clutch
Tank capacity .............................................450 ml
Spark plug ...............................Champion RCJ6Y
Fuel consumption (specifi c) ................. 582g/kWh
Sound and vibration
L sound pressure level ...................... 102 dB(A)
pA
K uncertainty .............................................. 3 dB
pA
L sound power level .......................... 112 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Anleitung_BG_CB_2041_T_SPK7.indb 23 Anleitung_BG_CB_2041_T_SPK7.indb 23
GB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
In operation
Vibration emission value a
h
K uncertainty = 3 m/s
2
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect condi-
tion.
•
Maintain and clean the equipment regularly.
•
Adopt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.

5. Assembly

Important!
Do not start the chainsaw until it has been fully
assembled and the chain tension has been adjus-
ted. Always wear protective gloves when working
on the chainsaw to protect yourself against injury.
-1
5.1 Joining the gear unit to the drive rod
mechanism (Fig. 4-6)
-1
Tools required: Allen keys size 4mm/5mm (sup-
plied)
Push the gear unit (Item 3b) and the drive rod
mechanism (Item 4) into each other. Center both
by turning the screw (Item K). Important! Make
sure that the screw (Item K) is turned exactly into
the guide hole (Item F). Otherwise there is a risk
of the upper part of the rod mechanism being
damaged. To join the two subassemblies securely
together, tighten the screw (Item I). To take apart,
proceed in reverse order.
5.2 Joining the drive rod mechanism to the
connecting piece (Fig. 7-10)
Open the handle screw (Item G) and push the
drive rod mechanism (Item 4) into the connecting
piece (Item 5). Make sure that the centering lever
(Item R) latches in the guide hole (Item H). Close
the guard cap (Item N) and tighten the handle
screw. To take apart, undo the handle screw and
open the guard cap. Press the centering lever and
simultaneously pull the drive rod mechanism out
of the connecting piece.
- 23 -
= 14.8 m/s
2
29.11.11 14:48 29.11.11 14:48