Operation; Switching Off The Engine - EINHELL BG-CB 2041 T Mode D'emploi D'origine

Filling the oil tank (Fig. 1):
Place the chainsaw on a fl at surface. Clean the
area around the oil tank cap (Fig. 3a) and then
clean the oil tank cap.
Fill the tank (Item 3a) with saw chain oil. In the
process, make sure that no dirt enters the tank,
as this could cause the oil nozzle to become blo-
cked. Close the oil tank cap.

7. Operation

Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
7.1 Starting with a cold engine
Fill the tank with the required amount of oil/petrol
mix. See „Fuel and oil".
1. Set the equipment down on a hard, level sur-
face.
2. Press the fuel pump (primer) (Fig. 2/Item 29)
10 times.
3. Move the On/Off switch (Fig. 2/Item 9) to „I".
4. Secure the throttle lever. To do this, press the
throttle lever lock (Fig. 2/Item 11) and then
press the throttle lever (Fig. 1/Item 12) and
lock the throttle lever by pressing the lock
(Fig. 2/Item 10) at the same time.
5. Set the choke lever (Fig. 2/Item 17) to „ ".
6. Hold the equipment fi rmly and pull out the
starter cable (Fig. 2/Item 14) until you feel it
begin to resist. Then tug sharply on the starter
cable 4 times. The equipment should start.
Important: Never allow the starter cable to
snap back. This may result in damage.
Once the engine has started, move the choke
lever immediately to „ " and allow the equip-
ment to warm up for approx. 10 seconds.
Important: Since the throttle lever is secured,
the cutting tool starts to operate when the
engine is started.
Then release the throttle lever by actuating it
once.
7. If the engine does not start up, repeat steps
4-6 above.
Please note: If the engine does not start up even
after several attempts, read the section „Engine
troubleshooting".
Please note: Always pull the starter cord out in
a straight line. If it is pulled out at an angle, then
friction will occur on the eyelet. As a result of this
friction, the cable will become frayed and will
wear away faster. Always hold the starter handle
Anleitung_BG_CB_2041_T_SPK7.indb 25 Anleitung_BG_CB_2041_T_SPK7.indb 25
GB
when the cable retracts.
Never allow the cable to snap back when it has
been pulled out.
7.2 Starting with a warm engine
(The equipment has been idle for less than 15-20
min.)
1. Set the equipment down on a hard, level sur-
face.
2. Switch the On/Of switch to „I".
3. Secure the throttle lever (in the same way as
described in „Starting with a cold engine").
4. Hold the equipment fi rmly and pull out the
starter cable until you feel it start to resist.
Then tug sharply on the starter cable. The
equipment should start after 1-2 tugs. If the
equipment does not start after 6 pulls, repeat
steps 1 – 7 of the procedure for starting the
engine from cold.
7.3 Switching off the engine
Emergency Stop procedure:
If it becomes necessary to stop the equipment im-
mediately, set the On/Off switch to „Stop" or „0".
Normal procedure:
Let go of the throttle lever and wait until the engi-
ne has changed to idling speed. Then set the On/
Off switch to „Stop" or „0".
7.4 Fitting the shoulder strap
Important! Always use the shoulder strap when
working with the equipment. Switch off the equip-
ment before you take off the shoulder strap (risk
of injury).
1. Slip the shoulder strap over your shoulder.
2. Adjust the length of the shoulder strap so that
the strap attachment is at waist level.
7.5 Work practice
Practice all the work steps with the engine swit-
ched off before you start to use the equipment.
- 25 -
29.11.11 14:49 29.11.11 14:49