General Safety Rules - Scheppach Slik 5.0b Manuel

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
plant with an air speed of at least 20 m/s.
Please observe the load values of the material manufac-
turer depending on the materials to be processed or the
material quality.
In these operating instructions we have marked the places
that have to do with your safety with this sign: m
m General Safety Rules
When using electric tools basic safety precautions should al-
ways be followowed to reduce the risk of fire, electric shock
and personal injury.
• Keep guards in place and in working order.
• Remove adjusting keys and wrenches. Form the habit
of checking to see that keys and adjusting wrenches are
removed from the machine before turning it on.
• Keep the working area clean. Cluttered areas and
benches invite accidents.
• Don't use in a dangerous environment. Don't use power
tools in damp or wet locations, or expose them to rain.
Keep work area well lighted.
• Keep children away. All visitors should be kept at a safe
distance from the work area.
• Make your workshop kid proof. Lock your workshop.
Tools not used should be kept in a dry place, inacces-
sible for children.
• Don't force the tool. It will do the job better and safer
at the rate for which it was designed.
• Use the right tool. Don't force the tool or attachment
to do a job for which is was not designed.
• Use proper extension cord. Make sure your extension
cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the cur-
rent your product will draw. An undersized cord will
cause a drop in voltage resulting in loss of power and
overheating.
• Wear proper clothing. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry which may
get caught in moving parts. Nonslip shoes are recom-
mended. Wear protective hair covering to contain long
hair. Roll your sleeves up to above the elbows.
• Protect your eyes by safety goggles. Everyday eyeglasses
offer only little protection. They are no safety glasses.
Wear a face or dust mask when working in a dusty en-
vironment.
• Secure work. Use clamps or a vice to hold work, when
practical. It is safer than using your hand, and it frees
both hands to operate the tool.
• Don't overreach. Keep proper footing and balance at
all times.
• Maintain tools with care. Keep tools sharp and clean
for best and safest performance. Follow the instructions
for lubricating, and changing accessories.
• Always disconnect the machine before servicing, and
when changing accessories, such as blades, bits, cut-
ters, and the like.
• Only use recommended accessories. Consult the oper-
ating instructions for the recommended accessories.
The use of improper accessories may cause risk of in-
jury to persons.
• Never stand on the machine. Serious injury could occur
if the machine is tipped or if the cutting tool is unin-
tentionally contacted.
10 english
• Check for damaged parts. Before further use of the tool,
a guard or other part that is damaged should be care-
fully checked to determine that it will operate properly
and perform its intended function. Check for alignment
or binding of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect its opera-
tion. A guard or other part that is damaged should be
properly repaired or replaced.
• Direction of work. Push the workpiece towards the
sawblade or cutter only in the moving direction of the
tool.
• Never leave the machine unattended while it is running.
Wait until the tool has come to an absolute standstill,
before you leave the machine.
• Use the correct power connection. Do not pull the power
plug to stop the machine during work. Never remove the
plug from the socket by pulling the extension cord.
• Always stay attentive to what you are doing, even when
using the machine regularly. Bear in mind that a frac-
tion of a second is sufficient to cause an injury.
• Keep your safety in mind. Safety is a combination of
common sense and staying alert as long as the ma-
chine is switched on.
Additional safety rules for the edge grinding machine
• WARNING: Do not use your machine until it is com-
pletely assembled and installed according to the in-
structions.
• If you are not familiar with the operation of the sanding
machine, ask the head of the department, your teacher,
or any other qualified person.
• ATTENTION: This machine has only been designed for
sanding wood or similar materials. The sanding of oth-
er materials can cause fire, injuries, or damage the
product.
• Always wear safety goggles.
• This machine may only be operated indoors.
• IMPORTANT: Mount and use the machine on a hori-
zontal surface. A non-horizontal surface can damage
the motor.
• If the machine tends to tilt or walk (especially when
sanding long and heavy panels), it must be fastened to
a solid surface of sufficient carrying force.
• Make sure the sanding belt runs in the correct direc-
tion – see arrows at the back of the belt.
• Make sure the sanding belt is running correctly so that
it cannot come off the drive pulleys.
• Make sure the sanding belt is not twisted or loose.
• Firmly hold the workpiece when sanding.
• Always use the fence when using the sanding machine
in horizontal position.
• Always hold the workpiece firmly to the table when us-
ing the sanding disc.
• Always hold the workpiece to the side of the sand-
ing disc running downwards, in order to maintain the
workpiece pressed to the table. By using the upward-
running side of the sanding disc, the workpiece could
be ejected and cause injury to persons.
• Always keep a minimum distance of about 1.5 mm or
less between the table or fence and the sanding belt
or disc.
• Do not wear gloves. Do not hold the workpiece with a
cloth during sanding.
• Use sanding belt or disc of the correct grit correspond-
ing with the wood.
• Never sand workpieces too small to be held safely.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

19033018011903301802

Table des Matières