Flotec FPRP3250C Notice D'utilisation page 3

Installation
b. Wear safety glasses at all times when
working with pumps.
c. Keep work area clean, uncluttered and properly
lit – replace unused tools and equipment.
d. Keep visitors at a safe distance from work area.
e. Make workshop child-proof – with padlocks,
master switches, and by removing starter keys.
11. When wiring an electrically driven pump,
follow all electrical and safety codes that apply.
12. this equipment is only for use on 115 volt
(single phase) and is equipped with an
approved 3-conductor cord and 3-prong,
grounding-type plug.
to reduce risk of electric shock,
pull plug before servicing. this pump has not
been investigated for use in swimming pool
areas. pump is supplied with a grounding
conductor and grounding-type attachment plug.
Be sure it is connected only to a properly
grounded grounding-type receptacle.
where a 2-prong wall receptacle is
encountered, it must be replaced with
properly grounded 3-prong receptacle
installed in accordance with codes and
ordinances that apply.
13. All wiring should be performed by a qualified
electrician.
14. Make certain power source conforms to
requirements of your equipment.
15. Protect electrical cord from sharp objects, hot
surfaces, oil, and chemicals. Avoid kinking
cord. Replace or repair damaged or worn cords
immediately.
16. Do not touch an operating motor. Modern
motors can operate at high temperatures.
17. Do not handle pump or pump motor with wet hands
or when standing on wet or damp surface, or in water.
hazardous voltage can shock, burn or
kill. if your basement has water or moisture on
floor, do not walk on wet area until all power has
been turned off. if shut-off box is in basement, call
electric company or hydro authority to shut-off
service to house, or call your local fire department
for instructions. remove pump and repair or
re place. failure to follow this warning can result in
fatal electrical shock.
Do not lift pump by power cord.
for emerGency flooDinG situations
hazardous voltage. can shock, burn or
kill. if your basement has water or moisture on
floor, do not walk on wet area until all power has
been turned off. If shut-off box is in basement, call
electric company or hydro authority to shut-off
service to house, or call your local fire department
for instructions. Remove pump and repair or re place.
For parts or assistance, call Flotec Customer Service at
Failure to follow this warning can result in fatal
electrical shock.
1. Install the adapter and hose barb in the pump's
check valve. Install the hose on the adapter and
clamp it.
2. Lift the cord and tape it to the pump's discharge
pipe. Plug the pump and switch into a UL and/or
CSA approved type SJTW water resistant 3-prong
grounding-type extension cord. The cord must
be at least #14 AWG and not more than 100 feet
long. Plugs and extension cord must be kept out
of the water.
3. Remove the old pump from the sump and set
it aside.
4. Lower the pump into the sump. Make sure the
power cord is long enough that the plug is out
of the water when the pump is running.
5. Run the hose out of the flooded area to an
adequate drain area.
6. risk of electrical shock.
Go to a dry area, remove wet shoes and change
wet clothing. WHEN YOU ARE DRY, plug the
extension cord into a grounded electrical outlet
(with a GFCI, if possible). DO NOT STAND IN
WATER TO PLUG IN THE PUMP.
7. National Electrical Code (NEC) and Canadian
Electrical Code (CEC) requirements prohibit the
use of an extension cord with this pump in a
permanent installation.
As soon as possible, remove the extension
cord and reinstall the pump as a permanent
replacement pump whose power cord connects
directly into a properly grounded grounding-type
receptacle. Install the pump in accordance with the
instructions, and in accordance with all codes and
ordinances that apply.
8. Monitor the pump's operation. The pump will
automatically stop when the water level has
receded to the OFF point of the switch.
notice: The use of an extension cord is not
CSA approved with this pump.
installation
1. Install pump in sump pit with minimum diameter
of 10" (254mm). Sump depth should be 10"
(254mm). Construct sump pit of tile, concrete,
steel or plastic. Check local codes for approved
materials and for proper installation.
2. Install pump in pit so that switch operating
mechanism has maximum possible clearance.
3. Pump should not be installed on clay, earth or
sand surfaces. Clean sump pit of small stones
and gravel which could clog pump. Keep
pump inlet screen clear.
notice: Do not use ordinary pipe joint
compound on plastic pipe. Pipe joint
compound can attack plastics.
1-800-365-6832
3