Output Connections; Analog Outputs Y; Digital Output U; Operation - Rotel RCD-1570 Manuel De L'utilisateur

Output Connections

The RCD-1570 gives you a choice of two different kinds of outputs – an
analog output signal from the built-in D/A converter for use with conventional
analog audio components and a coax digital output which provides an
unprocessed digital signal for use with outboard D/A converters or digital
processors.
NOTE: To prevent loud noises that could damage your speakers, turn
off all the system components when you make any signal connections.

Analog Outputs y

See Figure 3 and Figure 4
A pair of standard RCA jacks and XLR balanced connectors supplies an
analog output signal from the RCD-1570 to the source inputs of an audio
preamplifier, integrated amplifier, or receiver. You should choose only one
method of analog connection from the RCD-1570. Do not connect both the
RCA and XLR at the same time.
Select high quality audio interconnect cables. Connect the left and right
channel outputs of the RCD-1570 to the corresponding inputs on the
preamplifier or other component.

Digital Output u

See Figure 5
If you are using an outboard D/A converter or other digital processor, you
will need an unprocessed digital data stream from the RCD-1570. Using a
standard 75 ohm coax digital cable, connect the RCD-1570's digital output
to the digital input connector on the outboard D/A converter.
When playing CD-DA, MP3 and WMA discs the Digital Output provides
a PCM data stream.
NOTE: When an HDCD disc is played "HDCD" appears in the display.
However the analog output is not HDCD decoded.

Operation

The RCD-1570 can be operated using its front panel buttons or from
corresponding buttons on the supplied infrared remote control. Specific
instructions for each of these controls are detailed below. Most of the buttons
are duplicated on the front panel and on the IR remote control. However,
there are a few exceptions where the buttons are only available on one or
the other. These exceptions are noted in the instructions.

Infrared Remote Control 8

Before using the IR remote control, it is necessary to install two "UM-4/
AAA" batteries (supplied). Remove the plastic cover on the back of the IR
remote, install the batteries (observing the + and – polarity indications),
and reinstall the cover.
To use the IR remote control, aim it at the IR sensor
left corner of the RCD-1570 front panel.

Display 5

A lighted Display on the front panel of the RCD-1570 provides useful
information about the status of the unit, activation of special features, and
track/time information for the disc being played. Each of these indicators
is described in the detailed operating instructions that follow.

Disc Slot =

A disc slot located in the center of the RCD-1570, accepts the disc and
pulls it into the disc transport. Insert the disc label-side up. After the disc is
loaded the display shows the number of tracks on the disc.

Transport Control Buttons

These buttons provide basic control functions for the disc transport mechanism.
Except where noted, all functions are available on the RCD-1570 front panel
and the IR remote control.

PLAY Button qF

After the disc is loaded, press the PLAY
The number of the track being played and the elapsed time will be shown
in the display, along with the PLAY indicator. Normally, the disc will start
playing with the first track. However, you can select a different track using the
TRACK buttons or the DIRECT ACCESS buttons (see below) before pressing
the PLAY button to start playing a different selection.

STOP Button wE

Press the STOP
resume disc play where it was stopped. If the STOP
disc play stops, the display shows STOP and programmed selections are
deleted (see below). When the PLAY
STOP

PAUSE Button eN

The PAUSE
to spin and play will be resumed from the current position. The PAUSE
indicator will light in the Display. To resume playing the disc, press the
PAUSE button again or press the PLAY button.

TRACK Buttons rtO

These buttons are used to select tracks on the disc. When a disc is playing,
pressing the
Pressing the
Pressing
the previous track. The new track number appears in the Display.
These buttons are also used to select a track before pressing the PLAY button
or when memorizing tracks for the PROGRAM play mode (see below). These
selections are made by continuously pressing the TRACK buttons until the
desired track is reached.
In PROGRAM mode, the TRACK buttons advance or reverse to the next
track in the memorized selection list.
8
located in the lower
button once to stop disc play. Press the PLAY
button twice, the disc begins playing from the first track.
button is used to temporarily suspend play. The disc continues
TRACK button advances to the beginning of the next track.
TRACK button returns to the beginning of the current track.
TRACK twice quickly in succession returns to the beginning of
9
button to start playing the disc.
button to
button is press twice,
button is press after pressing the