Standard Delivery Content; Technical Specifications; General Features; Guard Trac™ Guardrail - Tractel guard trac Manuel D'installation

guardrail does not require any tools for
installation.
GB
The guard trac™ or guard trac™ plus guardrail
can be used on PVC or bonded bitumen sealing
coats in
1907/2006/CE and standard ISO11014 and
also EPDM type membrane (Two-leaf standard
mix synthetic vulcanised rubber 100% Ethylene-
Propylene-Diene Terpolymer) where the slope
must be less than 10°.
The guard trac™ guardrail is EN13374 class A
2019 certified.
The guard trac™ plus guardrail is EN13374 class
A 2019 and ISO 14122-3 2016 certified.

4. Standard delivery content

4.1. Standard delivery of a guard
trac™ guardrail
Standard delivery of a guard trac™ guardrail
consists of the following components:
•
2 concrete counterweights of 25 kg each
(fig. 1, rep. 1)
•
1 double bracket in cast iron with
cataphoretic protection, equipped with its
anti-slip pad and its guardrail locking
system (fig. 1, rep. 2)
•
1 x 3 m long aluminium barrier (fig. 1, rep.
3)
•
1 stainless steel latch (fig. 1, rep. 4)
•
One plastic bag containing this installation,
maintenance and servicing manual as well
as the identification plate.
Options available for the guard trac™ guardrail:
•
Concrete counterweight (fig. 1, rep. 1)
•
fully equipped double bracket (fig. 1, rep.
2)
•
long or short adjustable length aluminium
barrier
gearwheel (fig. 2)
•
adjustable aluminium gate equipped with
two tightening handles (fig.3)
•
stainless steel latch (fig. 13)
•
counterweight interface (fig. 17).
10
compliance with
equipped with its
4.2. Standard delivery of a guard
trac™ plus guardrail
Standard delivery of a guard trac™ plus guardrail
consists of the following components:
directive
•
4 concrete counterweights of 25 kg each
(fig. 4, rep. 1)
•
1 double bracket in cast iron with
cataphoretic protection, equipped with its
anti-slip pad and its guardrail locking
system (fig. 4, rep. 2)
•
1 single bracket in cast iron with
cataphoretic protection, equipped with its
pad and its guardrail locking system (fig. 4,
rep. 3)
•
1 x 3 m long aluminium barrier (fig. 4, rep.
4)
•
1 stainless steel latch (fig. 4, rep. 5)
•
1 inter-barrier link (fig. 4, rep. 6)10
•
One plastic bag containing this installation,
maintenance and servicing manual and
the installation identification plate.
•
1 counterweight interface (fig. 17)
Options available for the guard trac™ plus
guardrail:
•
Concrete counterweight (Fig. 4, rep. 1)
•
fully equipped double bracket (fig. 4, rep.
2)
•
fully equipped single bracket (fig. 4, rep. 3)
•
adjustable
equipped with its locking gearwheel (fig. 5)
•
inter-barrier link (fig. 4, rep. 6)
•
adjustable aluminium gate equipped with
two tightening handles (fg.3)
•
stainless steel latch (fig. 13)
•
2m aluminium barrier
•
counterweight block interface (fig. 17)

5. Technical Specifications

5.1. General features

locking
5.1.1. guard trac™ guardrail
The sizes given in the table below are referenced
in fig. 1.
L1 (mm)
3560
length aluminium
L2 (mm) d (mm) Sg (m²)
800 50 3
barrier