Briteq BT-575S Mode D'emploi page 7

ENGLISH
Home Position Adjust

Press MENU button for at least 5 seconds to
go into offset mode

Now you can adjust the home position ( this is
the zero position )

When you want to adjust gobo and color home
position, you should run mode first

The functions are shown below:
Pan offset

Press the MENU button for at least 5 seconds
to activate offset mode

Use DOWN and UP button until
shown on the display.

Press the ENTER button so the display starts
blinking.

Use DOWN and UP button to adjust the pan home position.

Once the position has is selected, press the ENTER button to setup OR Automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
Tilt offset

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until is shown on the display.

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the tilt home position.

Once the position has is selected, press the ENTER button to setup OR Automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
Focus Adjust
 Press the MENU button for at least 5 seconds to activate offset mode
 Use DOWN and UP button until
is shown on the display.
 Press the ENTER button and the unit will focus on "tilt 135°" position
 Press the ENTER button and the unit will focus on "tilt 45°" position
 Press the ENTER button and the unit will focus on "pan 0°" position
 Press the ENTER button and the unit will focus on "pan 90°" position
 Press the ENTER button and the unit will focus on "pan 180°" position
 Press the ENTER button and the unit will focus on "pan 270°" position
 In the Previous 6 steps you are able to adjust the focus with the UP/DOWN buttons on the unit
To go back to the main functions without any change wait 8 seconds .
Gobo1 offset

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until is shown on the display.

Press the ENTER button and the display starts blinking.

Use DOWN and UP button to adjust the gobo home position.

Once the gobo1 is selected, press the ENTER button to setup OR automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
BRITEQ®
OPERATION MANUAL
is
9/73
ENGLISH

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until

Press the ENTER button and the display starts blinking.

Use DOWN and UP button to adjust the gobo home position.

Once the gobo2 is selected, press the ENTER button to setup OR automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the color home position.

Once the color is selected, press the ENTER button to setup OR automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
HOW TO CONNECT THE UNIT BY DMX
The DMX-protocol is a widely used high speed signal to control intelligent light equipment.
You need to "daisy chain" your DMX controller and all the connected light effects with a
good quality XLR M/F balanced cable. To prevent strange behavior of the light effects, due
to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain. Never
use Y-splitter cables, this simply won't work!
Each light effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
BT575S BRITEQ®
Gobo2 offset
is shown on the display.
Color offset
is shown on the display.
10/73
OPERATION MANUAL
BT575S