Software Update - Steinberg Systems SBS-SF-1000 Manuel D'utilisation

Buzzer can be turned ON or OFF by moving the cursor to
"S: Q:" and pressing [OK], the keyboard will display the
signal strength and quality panel illustrated by progress
bars as below:
USALS - set the satellite location paramete. Move the
cursor to "USALS" and then press [OK] on the keyboard to
display the following screen:
EN
Longitude: longitude
»
Direction: satellite direction
»
Move: change the satellite dish position
»
To change the satellite dish position, press the [<]
»
[>] buttons on the keyboard to move the dish east
or west by 1 degree. Pressing and holding the [OK]
button will continuously rotate the dish until it is
released.
Goto: automatic rotation - press [OK] on the
»
keyboard to start
XX: automatic adjustment of the dish to a given
»
satellite
ZERO: turn to "0" position
»
Set Limit: setting the dish rotation limiter
»
To set the limiter, choose "LEFT" (left), "RIGHT" (right) or
"CLEAR" (clear) and press the [OK] button on the keyboard,
i.e. to set the extreme dish position. For instance, to set the
dish to the east, establish the platter in a given position,
then choose "EAST" and press the [OK] button to make the
angle of the given position the most east extreme, over
which the dish will not rotate. Choose "CLEAR" to reset the
limiter settings.
• SPECTRUM
In the Spectrum submenu, the graph shows the strength
of the input signal. The choice can be made with the
navigation buttons [˅] [˄] [<] [>] and confirmed with the
[OK] button.
Polarity: choosing V (vertical) or H (horizontal)
»
polarity
22K: turning on [ON]/turning off [OFF] the 22K signal
»
DISEqC1.0: turned off [OFF] or choosing a converter
»
- LNB1, LNB2, LNB3 or LNB4.
Switching between Polarity, 22K and DISEqC1.0
Press the [<] [>] buttons to move the cursor, press the [˄]
[˅] buttons to change the signal strength display range,
current frequency and signal strength are shown at the top.
Press [OK] to pause.
• LIST
In this submenu you can set the way of searching for
available satellites. Use the [˅] [˄] [<] [>] buttons to
choose automatic [Auto Check] or manual [Manual Check]
searching. Choose the satellite with the navigation cursors
and confirm the choice with [OK], and then select the
available transponder using the same buttons.
Manual Check – choose the desired satellite,
»
corresponding transponder and the
parameters will be shown- strength, quality, type,
FEC (error correction) and BER (bit error rate).
Auto Check – this function is used to check which of
»
the selected satellites can be connected to the line
quickly and easily. The satellite searching will stop
and the 'Lock' indicator will be displayed on the
device when the signal will be blocked.
Press [OK] to move to the searching for the next satellite.
• SAT
In this submenu, the user can add, modify or remove
satellites and their names, LO frequency, 22 KHz signal,
DISEqC 1.0, USALS and width according to personal
preferences.
10
• TP
In this submenu, the user can add, modify and remove
transponders and their frequency, data transfer speed and
polarization.
• SETUP
In this submenu, the user can manage device settings and
additional outputs.
Set OSD Language – choosing software language
»
Operate USB Disk – connecting to an external disk
»
via USB
signal
► Back up Data – creating backup on an external
storage medium
► Update Data – updating satellite data of an
external storage medium
CAUTION! Only a "txt" file named "sf700" can be recognized
by the device and should be saved as follows:
1 2 3 4
1. "01" means that the information in this line
concerns the satellite
2. satellite serial number, which must always be
in numerical order, i.e. it cannot go randomly,
e.g. from "01" to "03", etc.
3. satellite name (limited to 10 characters). To
name the satellite, e.g. "sat01", it must be
written as "00000sat01".
4. satellite LO frequency
5. 22KHz signal status: "0" - off, "1" - on
6. DISEqC1.0 status: "0" - off, "1" - LNB1, "2" -
LNB2, "3" - LNB3, "4" - LNB4.
7. USALS status: "0" - off, "1" - on
8. satellite longitude
9. satellite location: "0" - east, "1" – west
1 2 3
1. "001" means that the information in this line
concerns the transponder
2. transponder serial number, which must always be in
numerical order, i.e. it cannot go randomly, e.g. from
"01" to "03", etc.
3. the number indicates the transponder affiliation
the given satellite number, i.e. the satellite and
transponder numbers must be the same
4. transponder frequency
5. data transfer speed
6. polarization: "0" means H (horizontal) and "1" means
V (vertical).
► Reset to Factory – reset the information to
factory settings.
► Calculate Angle – the calculator of height,
azimuth and LNB polarization angle depending
on the longitude, longitude and latitude
parameters for the location. Helpful for receiving
the installation.
The letters "E", "W", "N" and "S" stand respectively for
eastern, western, northern and southern hemisphere. To
change, choose the letter using the [˅] [˄] buttons and
then choose the desired letter (direction) with the [<] [>]
buttons.
Information about the angles is recalculated and displayed
when the parameter is set. The angle of height above
sea level is calculated from the horizon upwards and the
azimuth angle is calculated from the north clockwise.
► Set compansation – sets the signal strength
correction value
► Select Power's Unit – select the unit of the signal
level value
► Change the Color – choose background color, font
and selection

3.3.1. SOFTWARE UPDATE

You can update the device's software via the USB port.
5 6 7 8 9
To update, connect a USB flash drive with the uploaded
software file, press and hold the flashlight button and, while
holding the button, turn the device on with the [POWER]
button, and release the flashlight button. After turning-
on, the display should immediately show the update file
(illustrative image):
Confirm the choice of the file with the [OK] button, and the
rest of the update process will proceed automatically. After
updating is completed, the system will restart.
11
4 5 6
EN