Accessories - Triton TPT 125 Instructions D'utilisation Et Consignes De Sécurité

Circuit breaker
• A circuit breaker is installed next to the On/Off Switch (13)
• If excessive electric current is detected, the circuit breaker will shut off the
power supply to protect the motor
• Before resetting the circuit breaker check the motor, switch, and power
connection for short circuit or faulty components
• To reset the circuit breaker:
• Press the red (0) button so that the machine is turned off
• Press the Circuit Breaker Reset Button (12)
Planer operation
WARNING: Always use adequate protective equipment, including eye
protection, respiratory and hearing protection, when working with this tool.
• For best results, determine desired depth of cut and final thickness of
workpiece before planing. Since there is a limit to maximum depth of cut,
several passes may be required to achieve final thickness
• In general, thin cuts produce a better outcome in terms of smoothness of
finished surface, even thickness, less kickback, less snipe, and less wear
on the cutter head and motor
• To prevent kickback, never make cuts deeper than 2.4mm (3/32") in one
pass
• If more than one pass is necessary, the Rollercase must be lowered
manually before each pass
• Always set a thin depth of cut for hardwood, wide workpieces and
workpieces with an uneven surface
• Avoid wood stock with many or large knots, or with excessive twisting,
cupping, or bowing
• If necessary, process one side with a jointer or surface planer first to obtain
at least one flat surface before using the planer
• Plane both sides of the workpiece, removing half the total depth from each
side. This will produce two smooth surfaces with equal moisture content
and therefore a board less likely to warp when it dries naturally
• Make a test cut with similar material to check accuracy of the settings
before planing the workpiece
• Feed the workpiece 'with' the grain whenever as possible
• Provide suitable support for long or wide workpieces
1. Set up the planer for depth of cut required (see 'Setting the depth of cut'
above)
2. Stand on the side that the Crank Handle is fitted. Never stand directly in
front of the workpiece, and do not allow anyone to stand or cross in line
with blade rotation. Kickback or thrown debris will travel in this direction
3. Place the workpiece on the In-feed Table (10), with the surface to be
planed facing upwards
4. Turn the machine on and allow the cutter head to reach full speed
5. Holding the workpiece firmly, move it slowly towards and onto the in-feed
roller
NOTE: Never feed a workpiece into the planer via the out-feed table
6. Stop pushing the workpiece once it is engaged by the in-feed roller. The
in-feed roller will move the workpiece automatically through the planer
7. Do not force the cut. Slowing or stalling will overheat the motor
8. Always keep your hands well away from the blades or chip ejection area
while the motor is running
9. Support the weight of large workpieces as they move through the planer to
GB
stabilise the workpiece and reduce snipe
10. Move to the back of machine to receive the workpiece. Do not pull the
workpiece; allow the rollers to do the work
11. If a workpiece becomes jammed inside the machine, turn the machine off,
remove the plug from mains supply, raise the Rollercase away from the
workpiece and ALLOW THE MACHINE TO COME TO A COMPLETE STOP
12. Never reach into the machine whilst it is in operation or running down
8
13. Use in-feed and out-feed rollers or supports when working with long
workpieces
14. For precision woodworking, measure the thickness of the workpiece with
calipers or a digital thickness gauge after each pass

Accessories

• A range of accessories, including Dust Port Adaptors (224786), Dust
Collection Bucket (330055) and Planer Thicknesser Blades 2pk (300259) is
available from your Triton dealer. Spare parts can be purchased from your
Triton dealer or online at www.toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any
inspection, maintenance or cleaning.
WARNING: ALWAYS wear suitable cut proof gloves when handling the
Rollercase and its sub-components.
Note: Any damage to this tool should be repaired and carefully inspected
before use, by qualified repair personnel.
Note: Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
• This tool is manufactured using class leading components and makes
use of the latest in intelligent circuitry that protects the tool and its
components. In normal use it should provide a long working life
Cleaning and lubrication
• Keep your machine clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body of
your machine with a soft brush or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• After use, vacuum the planer machine to remove wood chips, sawdust and
debris
• Use a cleaning solution (not included) to remove resin and grease residue
• Remove sawdust, wood chips and grease from chains and gears
• The bearings in motor and cutter head units are factory-sealed and should
require no further lubrication
• Four components require regular lubrication:
• Rollercase vertical screw mechanism (x2)
• Rollercase lock cam
• Rollercase vertical rails (x4)
• Feed roller chain drive
• Remove the top and both side panels to access these components
• Clean the chain drive before lubrication. Use spray oil (not included) to
lubricate the chain. Allow time for the lubricant to penetrate between the
links, then wipe the surface of the chain dry
• Remove any residues of grease from the other components, using mineral
spirits if necessary, then apply a coat of light grade multi-purpose grease
(not included)
• The work table and extension table can be coated with a very thin coat
of lubricating wax (not included) to protect the surface from rust and to
facilitate smooth feed during operation
Re-aligning the Rollercase
• Test the blade alignment by running two pieces through each side (left and
right) of the planer
• Measure and compare results to check that the blades are correctly
aligned and/or to determine the amount of correction required
• To correct any misalignment:
1. Turn the planer off and remove the plug from the power source
2. Carefully place the planer on its back
3. Remove the screws to the horizontal spindle retaining bracket on the Crank
Handle (9) side of the planer (Image D)
Creation date: 10 August 2015 4:06 PM