Safety Label; Safety; General Safety Instructions; Instructions, Standards And Regulations - Stiebel Eltron SB 300 E Mode D'emploi

INSTALLATION

Safety

SB 400 E
M-NO.: 234111
S-NO.:
Technical data
Datos técnicos
Données techniques
Volume:
Volumen:
Volume:
413 l / 109.1 gal
Supply:
Alimentación:
Alimentation:
220-240 V AC, 60 Hz
SINGLE PHASE L-L ONLY
Power:
Potencia:
Puissance:
3 kW / 10,239 BTU/h
Max. pressure:
Presión máxima:
Pression max:
1 MPa / 145 PSI
Testing pressure:
Presión de prueba:
Pression d'essai:
1.5 MPa / 217 PSI
Standby loss:
Pérdida de calor:
Pertes en mode de veille:
3.0 kWh/24h
7.2

Safety label

CAUTION
To reduce the risk of electric shock or fire use only on a utility supply
having a maximum 250 volt, three wire system.
CAUTION
Risk of Electric Shock. Connect branch circuit equipment grounding
means to water heater. For detailed information, refer to instructions.
CAUTION
Risk of Electric Shock and Fire Hazard. Do not connect to supply
by extension cord.
FOR INSTALLED RATING SEE ELEMENT MARKING
Install temperature and pressure protective equipment required by
local codes, but not less than a combination temperature and
pressure relief valve certified as meeting the requirements for Relief
Valves and Automatic Gas Shutoff Devices for Hot Water Supply
Systems, ANSI Z21.22, by a nationally recognized testing laboratory
that maintains periodic inspection of production of listed equipment
or materials. The valve must be oriented, provided with tubing, or
otherwise installed so that discharge can exit only within 6 inches
(15 cm) above, or at any distance below, the structural floor, and
cannot contact any live electrical part.
CAUTION
If the water heater is retrofitted with supplemental heating
equipment, you must adjust both the thermostat controlling the
supplemental heat source (located in the water piping) and the
thermostat on the water heater (behind the access panel) to the
same temperature. Failure to adjust both thermostats to the same
temperature can cause loss of proper temperature control.
When a supplemental heat source is connected to the
appliance, a provision must be made to limit the heat
source temperature not to exceed that of the water heater
thermostat setting.
Safety label on the appliance
6 |SB 300-400 E
Made in EU
Hecho en EU
Fabriqué en EU
Heat exchanger
Intercambiador de calor
Échangeur de chaleur
Max. pressure:
Presión máxima:
Pression max.:
1 MPa / 145 PSI
Heating surface:
Superficie de calefacción:
Surface de chauffe:
2 2
1.92 m / 20.6 ft
Volume:
Volumen:
Volume:
11.1 l / 2.9 gal
Max. temp.:
Temperatura máxima:
Temp. max.:
95 °C / 203 °F
4010487
Conforms to UL STD. 174
Certified to CAN/CSA STD. C22.2 No.110-94
INSTALLATION
8. Safety
Only a qualified contractor should carry out the installation, com-
missioning, maintenance and repair of the appliance.
8.1

General safety instructions

To prevent the necessity of a warranty claim, use only origi-
nal accessories and spare parts. If you need spare parts, call
800.582.8423.
8.2

Instructions, standards and regulations

Note
Observe all applicable national and regional regulations
and instructions.
Take note of the appliance type plate and See 15, "Specifications",
pg. 12.
9.

Preparations

9.1

Transport

CAUTION Injury
!
Take note of the weight of the appliance.
Use suitable transport aids (e.g. a hand truck) and
enough personnel for transportation.
Caution
!
The appliance is top heavy.
Make sure the unit is not tilted.
Only set the appliance down on an even base.
Do not unpack the appliance until it has arrived in the final in-
stallation room.
Leave the appliance in its packaging and on the pallet. This enables
horizontal transport and provides places to rest during transport.
Vehicular transport
Caution
!
The appliance must generally be stored and transported
vertically.
Observe the information on the packaging.
www.stiebel-eltron-usa.com