Ryobi EasyEdge RLT5030S Manuel D'utilisation page 11

EN
DE
FR DE ES IT
FR EN ES IT PT
Deutsch(Übersetzung der originalen Anleitungen)
slightly damaged, carefully determine if it will operate
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, breakage of part's proper mounting and any
other conditions that may affect the operation of the
tool. A guard or other part that is damaged should
be properly repaired or replaced by an authorized
service facility unless otherwise indicated in this
Instruction Manual. Defective switches must be
replaced by an authorized service facility. Do not use
a tool if the switch does not turn the tool on and off
correctly.
Guard against electric shock. Prevent body contact
■
with 'grounded' objects such as water pipes,
radiators, cookers and refrigerator enclosures.
Use only approved parts. When servicing use only
■
identical replacement parts. Use an authorized
service facility to fit replacement parts.
Be aware of the harmful/toxic dusts arising from
■
grass trimming etc, (e.g. fertilizers, insecticides).
The use of improper accessories or attachments
■
other than recommended can lead to personal injury.
This electric tool is constructed in accordance with
■
the relevant safety requirements. Only experts may
repair the electric tool. Otherwise, it may endanger
your life.
Voltage — make sure power supply is correct for your
■
machine. The voltage of this machine is on the rating
plate.
IMPORTANT: additional safety notes for your Grass
Trimmer.
During assembly take great care when fitting the
■
guard as this has a very sharp cutting edge on one
side for cutting the nylon line.
Never hold the cutter head above foot height or point
■
it towards people or animals when in use.
If the trimmer starts to vibrate excessively switch
■
SYMBOL
Warning! Indicates a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
Read this safety and operating instructions in this booklet and keep it in a safe place for future
reference.
Wear eye protection.
Do not use this tool in the rain. Avoid using it in damp conditions.
RLT5030S 23lgs manual.indd 9 RLT5030S 23lgs manual.indd 9
PT NL SV DA NO FI HU CS RU
NL SV DA NO FI HU CS RU
English(original instructions)
SYMBOLS
9 9
RO PL SL HR ET
RO PL SL HR ET
off immediately and have it checked by a qualified
service engineer.
CAUTION: The cutting head continues to rotate
for a few seconds after switching off.
Always remove any sticks and stones etc. before
■
using the trimmer.
Keep hands and feet away from the cutting means at
■
all times and especially when switching on the motor.
Do not cross roads or gravel paths while operating
■
trimmer.
On steep slopes cut across the slope, never in an
■
up and down direction. Never run while using the
trimmer.
Never fit a metal replacement line.
■
Never use the trimmer while it is raining or in damp
■
weather.
Use the trimmer in daylight or good artificial light.
■
Never use when visibility is bad.
Do not overreach, keep proper footing and balance at
■
all times.
Take care against injury from any device fitted for
■
trimming the filament line length. After extending new
cutter line always return the machine to its normal
operating position before switching on.
Always ensure the ventilation openings are kept clear
■
of debris.
If the cord is damaged during use, disconnect the
■
cord from the supply immediately. DO NOT TOUCH
THE CORD BEFORE DISCONNECTING THE
SUPPLY.
The appliance should be supplied via a residual
■
current device (RCD) with tripping current not more
than 30mA.
Never allow children or people unfamiliar with the
■
instructions to use the machine.
SAVE THIS MANUAL FOR FUTURE REFERENCE
EXPLANATION
LT LV SK BG
LT LV SK BG
2009/11/16 2009/11/16 3:44 3:44