Setting Parameters - Hilti PP 10 Mode D'emploi

The LED begins to blink as soon as the tool's compens-
ation range is exceeded.
7.14 Fitting the screw feet and centering screw 10
Fit the appropriate feet for the pipe diameter before
setting up the laser in the pipe.
7.16 Target plate, front 11
Locking screw
@
Target plate, small
;
Bubble level
=
Target plate holder
%
7.17 Target plate, rear (2) 11
Reflective stripes (only for the PP 11)
&

7.18 Setting parameters

7.18.1 Setting units of measurement to % or ‰
1. Press the ON / OFF button and the LOCK button at
the same time.
The set values are shown in the display.
2. Use the laser beam UP / DOWN button to move to
the "unit" line.
3. Select the value you wish to change by pressing the
direction control button.
4. Press the SET button to confirm the entry.
The tool then returns to the normal operating mode.
7.18.2 Setting and activating the security code
Unauthorized persons can be prevented from using the
laser tool by entering a 4-digit security code. Please note
that once the security code has been activated, the laser
tool can no longer be operated without entering this code.
The code will be requested automatically after the tool is
switched on.
1. Press the ON / OFF button and the LOCK button at
the same time.
The set values are shown in the display.
2. Use the laser beam UP / DOWN button to move to
the "input S code" line.
3. Press the SET button to enter the correct mode.
4. The laser beam UP / DOWN button and direction
control button can be used to navigate to the corres-
ponding number. Press the SET button to confirm
the number selected. Press the SET button to con-
firm the code as soon as the four desired digits are
displayed in the "code" area of the display.
NOTE
Feet are available in the sizes 150 mm, 200 mm, 250 mm
and 300 mm (6", 8", 10", 12").
7.15 Setting the target plate size 11
Set the target plate size to a value suitable for the pipe
diameter you are working with.
Secures the target plate at the desired height.
Target plate for 150 mm to 250 mm.
For setting up the target plate horizontally.
For automatic alignment.
5. The display then returns to the previous mode. The
security code can then be activated ("on" by press-
ing the SET button) or deactivated later ("off" by
pressing the SET button again).
The tool then returns to the normal operating mode.
7.18.3 Entering the name of the company
These instructions describe how to enter or change the
name of the company. A maximum of 32 characters (16
characters in 2 rows) can be entered.
1. Press the ON / OFF button and the LOCK button at
the same time.
The set values are shown in the display.
2. Use the laser beam UP / DOWN button to move to
the "change name" line.
3. Press the SET button to enter the correct mode.
4. Use the laser beam UP / DOWN button and direc-
tion control button to navigate to the corresponding
characters / digits. Press the SET button to con-
firm the character selected. Press the SET button
to confirm the entry as soon as the correct name /
designation is displayed.
The tool then returns to the normal operating mode.
7.19 Checking the tool's accuracy 12
1. Set the laser to an inclination of 0.000%.
2. Set up a leveling staff at a distance of 1m and a
second leveling staff at a distance of 60m. Note the
heights at which the laser beam strikes the staffs.
3. Set up an optical level in the middle between the
two leveling staffs and read the heights from both
staffs.
4. Calculate the difference in height indicated by the
optical level and the rotating laser on staffs 1 and
2. If both values are identical, then the laser tool is
correctly adjusted.
NOTE If the differences X1 and X2 are not equal,
please contact your local Hilti Center or Hilti repres-
entative.
en
21