Adjusting The Dvd Level; Storing Settings In The Memory; Recalling The Preset Memory; Using The Pro Logic Ii Mode - Alpine IVA-D106 Mode D'emploi

Adjusting the DVD Level

The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.
Setting item : DVD LEVEL
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
Adjust the level by touching [ ] or [ ] of the desired
adjusting mode.
The level can be adjusted in the range of –5 to +5.

Storing Settings in the Memory

Adjustment or setting contents can be stored.
Contents that can be stored vary depends on the audio processor used.
1
Touch [MEMORY] on the A.PROCESSOR list
display.
2
Within 5 seconds, touch any one of the preset
buttons [P.SET 1] through [P.SET 6] on the
A.PROCESSOR list.
The setting contents are stored.
• The stored contents will not be deleted even when the battery power
cord is detached.

Recalling the Preset Memory

Touch Preset buttons [P.SET 1] through [P.SET 6] on
the A.PROCESSOR list to select the preset memory you
want to recall from Preset buttons.
• It takes a few moment to recall the preset memory.

Using the Pro Logic II Mode

Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a "REAR
FILL" function for outputting the signals of the front channel to the rear
channel.
Setting item : DOLBY PLII/REAR FILL
Touch [ ] or [ ] of DOLBY PLII/REAR to select the
desired mode.
PL II MOVIE: Suits the stereo TV shows and all programs
encoded in Dolby Surround. It improves the
sound field directivity to near that of discrete
5.1-channel sound.
PL II MUSIC: Can be used for all stereo music recordings, and
provides a wide, deep sound field.
OFF: Turns DOLBY PL II function to OFF.
56
-EN
If PL II MUSIC is selected, the center width can be adjusted with
following operations.
This function offers the optimum vocal position by adjusting the
center channel position between the center speaker and the L/R
speaker. (The adjustments established in "Adjusting the
acoustic image (BI-PHANTOM)" (page 55) are ineffective while
this function is activated.)
Touch [ ] or [ ] of CENTER WIDTH CONT. to adjust the
level.
The level can be adjusted between 0 to 7. When the level
increases, the center channel position moves from the
center speaker position to both sides.
Touch [OFF] of CENTER WIDTH CONT. to turn off the
center width control.
• This adjustment is effective when the setting of the center speaker is
SMALL or LARGE in the speaker setup settings.
• "REAR FILL" function
Depending on the input signals, the sound may only be output from
the front speakers. In this case, the "REAR FILL" function can be
used to output signals from the rear speakers as well.
• If REAR FILL is set, 192 kHz, 96 kHz, etc., contents are down
sampled to 48 kHz.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 51).
• This function only works with two-channel signals. This operation is
ineffective when 5.1-channel DTS or Dolby Digital signals are input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound is
unchanged in the rear fill setting because REAR MIX is given priority
during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• Touching [RETURN] will return to the previous screen.

Linear PCM Setting

The output when playing discs recorded in linear PCM can be set to 2 or
3 channels.
Setting item : PCM MODE
Touch [ ] or [ ] of PCM MODE to select 2CH or 3CH.
2CH: 2ch output (L/R)
3CH: 3ch output (L/R/CENTER)
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 51).