Alpine IVA-D106 Mode D'emploi page 29

Adjusting the Fader
Touch [F] or [R] to adjust the volume of the front and
rear speakers.
Setting range: F15 to R15
• Determine your desired setting value by touching and moving [
• If you set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch of
the IMPRINT audio processor (PXA-H100) to 2.2ch (3WAY), you
cannot adjust the FADER mode. For details, refer to the Owner's
Manual of PXA-H100.
Adjusting Bass/Treble
You can change the bass or treble frequency emphasis
to create your own tonal preference.
Touch [ ] of BASS/TREBLE to adjusting screen.
• When an external audio processor is connected, the list is not
displayed.
• If OFF is set in "Changing MultEQ mode" (page 43) when the
IMPRINT audio processor is connected, the list is not displayed.
Setting the Bass level
You can emphasize or weaken the bass frequency.
Touch [ ] or [ ] of BASS LEVEL to select the desired bass level.
Setting range: -7 to +7
Setting the Bass Center Frequency
The displayed bass frequency is emphasized
Touch [ ] or [ ] of BASS FREQ. to select the desired bass
center frequency.
Setting range: 60 Hz, 80 Hz, 100 Hz, 200 Hz
Setting the Bass Bandwidth (Q-Factor)
Changes the boosted bass bandwidth to wide or narrow. A
wide setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
Touch [ ] or [ ] of BASS BANDWIDTH to select the desired
bass bandwidth.
Setting range: WIDE1 (1), WIDE2 (1.25), WIDE3 (1.5),
WIDE4 (2)
• The bass level settings will be individually memorized for each
source (FM, AM, CD, etc.) until the setting is changed. The bass
frequency and bass band width settings adjusted for one source are
effective for all other sources (FM, AM, CD, etc.).
Setting the treble level
You can emphasize the treble frequency.
Touch [ ] or [ ] of TREBLE LEVEL to select the desired treble
level.
Setting range: -7 to +7
Setting the Treble Center Frequency
The displayed Treble frequency is emphasized.
Touch [ ] or [ ] of TREBLE FREQ. to select the desired treble
center frequency.
Setting range: 10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz
• The treble level settings will be individually memorized for each
source (FM, AM, CD, etc.) until the setting is changed. The Treble
frequency settings adjusted for one source are effective for all other
sources (FM, AM, CD, etc.).
Setting the Loudness
Loudness introduces a special low- and high-frequency
emphasis at low listening levels. This compensates for
the ear's decreased sensitivity to bass and treble sound.
Touch [
Touch [ ] or [ ] of LOUDNESS to set to ON or OFF.
].
• The Loudness item is not displayed when an external audio processor
is connected.
Adjusting Highpass Filter
:
With the car stopped and Defeat set to off, touch [
H.P.F. to adjust screen.
Touch [ ] or [ ] to adjust the desired speaker.
• Select OFF when no adjustment is required.
• The H.P.F. item is not displayed when an IMPRINT audio processor
or external audio processor is connected.
Subwoofer On and Off
Touch [ ] or [ ] of SUBWOOFER to set to ON or OFF.
OFF : Subwoofer output is off.
ON:
Adjusting the Subwoofer Level
When ON is set in "Subwoofer On and Off", the item is displayed.
When an external audio processor is connected, the list is not displayed.
1 Touch [
The display changes to the SUBWOOFER Adjusting screen.
2 Touch [
Switching the Subwoofer phase
The setting range is displayed when the optional IMPRINT audio
processor is connected, "Changing MultEQ mode" (page 43) is set to
OFF, and "Subwoofer On and Off" is set to ON while the car is stopped.
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°).
1 Touch [
The display changes to the SUBWOOFER Adjusting screen.
2 Touch [
] of BASS/TREBLE to adjusting screen.
Setting range: OFF, 80 Hz, 120 Hz, 160 Hz
Subwoofer output is on.
] of SUBWOOFER.
] or [ ] of LEVEL to adjust the subwoofer output.
Setting range : 0 to 15
] of SUBWOOFER.
] or [ ] of PHASE to select to 0° or 180°.
] of
27
-EN