Setting The External Device Interrupt Mode; Setting The Interrupt Icon Display; Switching The Function Of The Remote Sensor; Setting The Navigation Mode - Alpine IVA-D106 Mode D'emploi

Setting the External Device Interrupt Mode

If an Alpine Ai-NET Auxiliary Input Adapter (KCA-801B) is
connected to the IVA-D106, an Auxiliary Source will be allowed to
interrupt the current audio source. For example, you can listen to a
portable MP3 player through your car audio system even with a CD
changer connected and playing. The CD changer will automatically
mute when switched to the AUX Input. For further details on how to use
the Alpine KCA-801B, see your authorized Alpine dealer.
Setting item: IN INT. MUTE
Setting content: OFF / ON
OFF: The volume level can be adjusted in Interrupt mode.
ON: Sound will not be output.
• The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
• If ADAPTER or NAV. is set in "Setting the Bluetooth Connection
(Bluetooth IN)" (page 39), the IN INT. MUTE setting item is not
displayed.

Setting the Interrupt Icon Display

The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN INT. ICON
Setting content: INT / TEL
INT: The INT icon appears on the display.
TEL: When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Switching the function of the remote
sensor
For remote control operation, the remote sensor of the external device
(monitor, etc.) can be switched, as you prefer.
Setting item: REMOTE SENSOR
Setting contents: FRONT / REAR
FRONT: The remote sensor of this unit is effective.
REAR: The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
• The touch panel rear monitor sensor has priority over the remote
control sensor. If the rear monitor (connected to the Alpine rear
monitor output via the Monitor control lead) is touched, the
command is executed regardless of the remote control sensor switch
setting. Note, however, that the remote control sensor that has been
set takes priority if it has been 5 seconds since last touching the
panel.
• When an optional DVD changer or DVD player is connected, and the
remote control sensor is set to REAR, some onscreen button
operations ( [ ] STOP, etc.) cannot be performed.
In this case, set the remote control sensor to FRONT.
38
-EN

Setting the Navigation Mode

When you connect an optional navigation equipment, set it to ON.
Setting item: NAV. IN
Setting contents: OFF / ON
ON: Navigation source is displayed.
OFF: Navigation source is not displayed. The settings related
to the navigation can not be changed from this unit.

Setting the Navigation Interruption

With an Alpine navigation system connected to the IVA-D106, the voice
guidance of the navigation system will be mixed with the radio or CD
play.
Setting item: NAV. MIX
Setting content: OFF / ON
OFF: The navigation interruption mode is turned off.
ON: The navigation interruption mode is on.
See "Adjusting NAV. LEVEL" under "Adjusting the Audio (Adjust
the Balance/Fader, Bass/Treble, Loudness, Highpass Filter,
Subwoofer, NAV. LEVEL, Defeat)" on page 28 to set the
navigation interruption volume level.
• The volume level for voice prompts during navigation guidance is set
by adjusting the its volume while the prompts are announced. When
the announcement finishes, the normal audio volume and the
previous audio screen are restored. The voice prompt volume is
always at or below the current listening volume. If a navigation
announcement cuts in while adjusting the audio level, it always resets
to the current level regardless of the audio level setting.
• This setting is effective when NAV.IN of SYSTEM list screen is ON.

Setting for iPod Connection

Set when an optional iPod or an external input device is to be connected.
Setting item: iPod
Setting contents: AUDIO / VIDEO / AUX+
AUDIO: Input is available for iPod audio (a video compatible
iPod is available only for audio input).
VIDEO: Set when a video compatible iPod is connected to
the iPod (V)/CAMERA connector. Image from the
iPod is input. If this setting is made, connect the
iPod to the Back-up camera by referring to
"Connecting Video compatible iPod and Back-up
Camera at the same time" (page 85).
AUX+: Set if an optional iPod Direct/RCA Interface cable
(KCE-236B) is connected to the iPod direct cable of
this unit.
A portable player, etc., with an RCA audio output
can be input to the unit. In this case, an iPod cannot
be connected. The "iPod" source name on the
SOURCE selection screen will not be displayed.