Initial Operation - Metabo ASR 25 L SC Notice D'utilisation Originale

Certain kinds of dust are classified
as carcinogenic, such as oak and
beech dust, especially in
conjunction with additives for wood
conditioning (chromate, wood
preservative).
5. Overview
See page 3.
1 Rotary switch On/Off/Automatic/SelfClean (SC)
2 Volume flow control display
3 Plug socket for power tool
4 Rotary switch for selecting the extraction hose
diameter *
5 PE filter bag *
6 Fleece filter bag*
7 Cable holder
8 Upper part
9 Snap lock
10 Bottom part
11 Suction opening
12 Sealing plug (for ASR 25 M SC,
ASR 50 M SC only) *
13 Locking knob
14 Locking bar (for opening the hood to change
filter cassettes)
15 Motor protection filter
16 Filter cassette (according to IFA C)
* depending on equipment/not included in scope of
delivery

6. Initial Operation

Before plugging in the device, check that
the rated mains voltage and mains
frequency, as specified on the rating label,
match your power supply.
6.1 Securing the sealing plug (for
ASR 50 M SC only)
Fit the chain of the sealing plug (12) in the bore of
the suction opening (11).
6.2 Fitting wheels (if necessary)
Insert the axles of the guide rollers in the holes
in the container until they engage.
Fit the large wheels as shown:
6.3 Inserting a Fleece Filter Bag
We recommend using paper and fleece filter bags
for:
- Applications, where small amounts of fine dust are
created (e.g. spot-grinding and grinding of paint
and lacquer coatings, extraction of drilling
applications with small diameters < 10 mm of
short duration, etc.).
- Use of machines, such as: routers, planers, small
grinding machines, etc.
Switch off the appliance, remove the mains plug
and open the snap locks (9). Remove the upper part
(8) from the container (10).
paper
upwards. (To twist the slide, push it slightly towards
the suction hose, and pull it back after twisting).
Holding the new fleece filter bag by the flange, slide
the bottom part over the suction connection, and the
top part over the latch pin. Replace the upper part of
the appliance on the container, close the snap
locks.
ASR 25 M SC:Turn the red
rotary switch (on the inside of
the suction opening) until the
stop: the text "CLOSE" shows
upwards to the marking ▲.
Hold the fleece filter bag on the flange and, with its
opening, guide it first over the latch at the bottom
part of the suction opening, then fit up to the stop on
the suction opening. Replace the upper part of the
device on the container, close the snap locks.
6.4 Inserting PE filter bag (for ASR 50 M SC
only)
PE filter bags (5) are suitable for both wet and dry
vacuuming.
We recommend the use of PE-disposal bags for:
- Applications, where larger amounts of dust are
created (e.g. removal of plaster surfaces, spot-
grinding and grinding of screeds, etc.).
- Use of machines, such as e.g.: renovation milling
machines, renovation grinders, drywall grinders,
wall grinders etc.
When using a PE disposal bag, the filter cleaning
must be switched on (function AR / IR) for
corresponding materials (see recommendation).
Switch off the appliance, remove the mains plug
and open the snap locks (9). Remove the upper part
(8) from the container (10).
plastic
(To twist the slide, push it slightly towards the
ENGLISH en
ASR 50 M SC: On
the inside of the
suction opening,
push the red rotary
slide with its
"triangle" marking
ASR 50 M SC: On
the inside of the
suction opening,
push the red rotary
slide with its "circle"
marking upwards.
17