Festool CARVEX PS 400 EBQ Notice D'utilisation D'origine page 16

CARVEX
GB
Ejecting saw blade
L When ejecting the saw blade, hold the
electric power tool such that no persons
or animals can be injured.
X
Push the saw blade ejection
wards as far as the stop.
If the saw blade is not ejected: run jigsaw
3 - 10 seconds at a high speed. Actuate saw
blade ejector mechanism
7.2 Using the chip guard
The chip guard [3-1]
away and improves the efficiency of the chip
extraction system.
X Using minimal pressure, push the chip
guard [3-1] downwards.
7.3 Inserting splinterguard
The splinterguard makes cuts with splinter-
free cutting edges possible, even on the exit
side of the saw blade.
X
With the machine switched off, push the
splinterguard [4-1]
the saw blade [4-2],
X
switch on the jigsaw,
X with the machine running (Speed range
5), push the splinterguard in on a flat
plane until it is flush with the front edge of
the saw table. This beds in the splinter-
guard.
L When it is worn, push the splinterguard
approx. 3 mm further to the rear and con-
tinue using it.
L To guarantee reliable operation of the
splinterguard, it must seal tightly on both
sides of the saw blade. For splinter-free
cuts, therefore, a new splinterguard
should also be used after every saw blade
change.
7.4 Changing saw table
X
Open the change lever [1-9].
X
Removing the saw table downwards.
L Assembly is performed in reverse se-
quence to removal. Ensure that the saw
table is firmly seated in the guide.
Instead of the saw table, the angle table WT-
PS 400 or adaptation table ADT-PS 400 can
be installed at the support.
Never saw without the saw table, or
one of the other tables offered in the
Festool accessories program.
16
[3-3] for-
[3-3] once again.
prevents chips flying
onto the guide up to
7.5 Dust extraction
WARNING
Dust hazard
X Dust can be hazardous to health. Always
work with a dust extractor.
X
Always read applicable national regula-
tions before extracting hazardous dust.
The extraction adapter
to be connected to a dust extractor (hose di-
ameter 27 mm).
X Insert the extraction adapter into the rear
opening of the saw table so that the hook
[5-2] engages in the
X To remove the extraction adapter, press
the hook [5-2].
L Due to the low power consumption of the
machine (low energy consumption), dust
extractors with an automatic switch-on
function will only start up when the actual
cut is made.
X Set the dust extractor to continuous oper-
ation for special applications (e.g. low
stroke rate, soft wood).
7.6 Adjusting the pendulum stroke
In order to process different materials with
an optimum feed movement the pendulum
jigsaws have an adjustable pendulum stroke.
Select the desired setting with the pendulum
stroke switch [1-12]:
setting 0 = pendulum stroke off
setting 3 = maximum pendulum stroke
Recommended settings of the pendu-
lum stroke
Hard and soft wood,chip board,
wood fibre board
Wood core plywood, plywood, plas-
tics
Ceramic
Aluminium, NF metals
Steel
7.7 Stroke speed control
The number of strokes can be adjusted step-
lessly with the adjusting wheel
tween 1500 and 3800 rpm (PSB 400 EBQ:
1000 - 3800 rpm). This enables you to opti-
mise the cutting speed to suit the respective
material.
[5-3] allows jigsaws
[5-1] recess.
1 - 3
1 - 2
0 - 2
0 - 1
[1-5] be-
0