Tightening And Checking The Saw Chain; Lubricating The Chain; Sharpening The Saw Chain; Initial Use - FLORABEST FHEHS 900 A1 Traduction Des Instructions D'origine

Tightening and checking the saw chain

NOTE
► The tension of the saw chain
GB
functioning of the appliance. A correctly tensioned saw chain
IE
increases the service life of your appliance.
WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
♦ Loosen the nut a little using the mounting tool
♦ Turn the chain tensioner screw
wise direction to increase the tension.
♦ Using the mounting tool
anti-clockwise direction to decrease the tension.
♦ The saw chain must lie against the underside of the blade. Check
whether the saw chain
♦ Tighten the nut again using the mounting tool
NOTE
► When drawing on the saw chain
traction, the saw chain
apart.
► A new saw chain
► Each time the appliance is used, the chain tension is to be checked
beforehand.

Lubricating the chain

♦ Remove the oil filler cap
♦ Fill the oil tank with approx. 100 ml of organic chain oil
WARNING!
► Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irre-
parably damaged in a short time. Always check chain lubrication
and oil level in the tank before starting work.
NOTE
► Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
► While working, check whether the automatic chain lubrication is
working correctly. Check the chain lubricator before and during
work.

Sharpening the saw chain

NOTE
► A grinder can be attached to the grinder support
grip during grinding.
► You will find detailed information on sharpening in the sharpening
set, e.g. from Oregon.
► Alternatively, you can use an electrical saw chain sharpening device
and follow the instructions of the manufacturer.
► If you have any doubts about implementing the work, the saw chain
should be replaced.
8
is important for your safety and the
.
with the mounting tool
, turn the chain-tensioner screw
can be drawn by hand over the blade
.
applying 9 N (approx. 1 kg)
and blade should be no more than 2 mm
stretches and must be tightened more regularly.
.
for a secure

Initial use

NOTE
► Comply with regulations regarding noise protection and local rules.
Using the appliance on certain days (e.g. on Sundays and public
holidays), during certain times (midday period, night time) or in certain
locations (e.g. health resorts, clinics, etc.) may be restricted or
prohibited.
Switching on and off
Switching on:
♦ Connect the power cord
in a clock-
♦ Form a loop at the end of the extension cable and attach this to the
strain relief .
in an
♦ Press the safety lock-out
on/off switch
.
Switching off:
♦ Release the on/off switch
♦ Remove the extension cable from the strain relief
♦ Disconnect the power cord

Adjusting the handle

♦ Press the release button
♦ Turn the turning element
button ; this must click into place.

Working with the hedge trimmer

.

Cutting techniques

■ See fold-out page (Figure A).
NOTE
► Remove thicker branches with a branch cutter.

Working with the pole pruner

Sawing techniques

WARNING!
► Pay attention to falling clippings.
► Be aware of the danger of branches flying back.
NOTE
► Place the stop
and quietly.
► Only then can you begin with the sawing.
Sawing off small branches
♦ Saw small branches (Ø 0–8 cm) from the top down (see figure).
to the extension cable.
and keep it pressed and then press the
.
.
from the extension cable.
.
to the desired position. Let go of the release
on the branch. This will help you work more safely
FHEHS 900 A1
.