Attachment And Operation - Scheppach MFH5300-4BP Traduction Des Instructions D'origine

Mixed fuels, which have been left unused for a pe-
riod of one month or more, may clog the carburetor
or result in the engine foiling to operate property. Put
remained fuel into an airtight container and keep it in
the dark and cool room.
2 Fuel mixing table
Mixing procedure: 40 parts petrol to 1 part oil
Example:
1 l Petrol : 0,025 l 2-stroke oil
5 l Petrol : 0,125 l 2-stroke oil
Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add
fuel to a machine with a running or hot engine.
Take care of fire!
Only ever refuel the tool outdoors or in suffi-
ciently ventilated rooms. Make sure not to spill
fuel or chain oil into the soil (environmental pro-
tection). Use a proper base.

8. Attachment and operation

ASSEMBLY
When assembling this machine, please follow the
instructions for assembly printed.
1 Assemble the handle on the machine. Fig. 2-3
• Install the front handle as shown on the image 2.
• Make sure that you align the pin with the hole.
Tighten the screws only loosely before you have
the most comfortable working position set to the
risers. The front handle should be aligned as in
pictures 2+3 shown, then tighten the screws.
2. Mounting the shaft. Fig. 4
• Pull out the locking pin (a) and press the lower part
of the shaft (b) downward until the locking pin en-
gages. The bolt (a) is in the right position when it
is fully seated in the bore.
• Lastly, tighten the knob (d) securely.
3. Assemble the safe guard. Fig. 5-7
• Fix the safe guard with hex key and wrench en-
closed as standard accessories for tighting the
nuts enough. Please see the below pictures show-
ing.
m Warning! Never use the machine without the
guard assembled!
4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 8-9
• Release the nut.
Line up the two holes of flange and shield, use
one screw driver to hold the flange as below and
turn the socket wrench clockwise, the nut will be
released.
38 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Fit the Nylon cutting head.
Remove another shield after release the nut. Still
hold the flange, take the Nylon cutting head on the
shaft and rotate counter­clockwise, the Nylon cut-
ting head is fitted. Fig. 9
• Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 10­12
Take the outer flange off after release the nut, then
put the blade (17), outer flange (17b), shield (17a)
and nut according to priority as below picture. Note
the blade rotation direction needs be same as be-
low picture. Use screw driver to hold flange and
tighten nut counter-clockwise, ensure the nut is
tightened enough.
• Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
m Warning!
Please make sure the cutting head has been assem-
bled correctly before use!
OPERATION
When working with the equipment as grass trimmer
and brush cutter, the appropriate plastic guard hood
for cutting blade mode or cutting line mode must
be fitted to prevent objects being thrown out by the
equipment.
The integrated blade (A) in the cutting line guard
hood automatically cuts the line to the optimum
length. Fig. 25
5 Mounting the flexible shaft Fig. 13 - 24
• Pull the locking bolt out and affix the flexible shaft
to the motor until the locking bolt locks in. Fig.
13, 14
• Open the air filter cover, screw the accelerator ca-
ble in as shown and attach to the throttle valve.
Fig. 15­ 17
• Secure with a counter nut. The accelerator cable
must be able to move from idle to full acceleration
freely. Fig. 18
• Connect the ignition interruption cables as shown
in figure 19, 20.
• Secure the air filter cover with a screw again. Fig.
21
• Remove the screw from the handle, insert the oth-
er side of the flexible shaft into the handle and use
the screw to affix it to the handle. Fig. 22, 23
• Use cable ties to affix the accelerator cable to the
flexible shaft. Fig. 24
6. Fit the belt. Fig. 56 - 60
• Wear the shoulder strap. Fig. 56 ­ 58
• Balance the machine when the tool is switched off.