Technical Data; Before Starting The Equipment - Scheppach MFH5300-4BP Traduction Des Instructions D'origine

6. Technical data

MFH5300-4BP
Technical data
Cutting data grass trimmer
Cutting circle diameter
of line mm
Cutting line diameter
mm
Cutting line length m
Speed grass trimmer
max. min¹
Cutting data brush cutter
Cutting circle diameter
of blade mm
Cutter balde thickness
mm
Teeth quantity
Speed brush cutter max.
min¹
Cutting data hedge trimmer
Cutting circle diameter
mm
Angle adjustment °
Cutting length mm
Max. cutting speed max.
min
-1
Cutting data pole saw
Bar length mm
Cutting length mm
Cutter bar Type
Saw chain division
Chain type
Chain link thickness
Oil tank capacity cm
3
Speed Pole saw min.
min
-1
Power unit
Displacement cm³
Max. engine output kW
Idle speed min
-1
Fuel tank capacity cm
3
Engine type
Weight grass trimmer
kg
Weight brush cutter kg
Weight pole saw kg
Weight hedge trimmer
kg
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 97,3 dB(A)
pA
Sound power L = 115,2 dB(A)
WA
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
450
2 x 2.8
4
7200
255
1.4
3
8500
24
+90°/0°/­75° (165°)
400
1550
305
254
AL10-39-507P
3/8"
3/8.50­39
1,27
125
4200
51,7
1300
3000 ±300
960
2-stroke engine, air-
cooled
11,98
11,88
12,53
13,20
Uncertainty K = 3 dB(A)
PA
Wear ear­muffs.
The impact of noise can cause damage to hearing.
Vibration
Grasstrimmer: A = Front 6,67 m/s
hv
Brush cutter: A = Front 6,96 m/s
hv
Hedge trimmer: A = Front 6,62 m/s
hv
Pole saw: A = Front 6,62 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Before starting the equipment

Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
1 Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special
2­stroke engine oil. Mix the fuel mixture as indicated
in the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bot-
tle). Then shake the bottle well.
Never use oil for 4­cycle engine or use water cooled
2­cycle engine. It can cause spark plug fouling ex-
haust part blocking or piston ring sticking.
Rear 5,67 m/s
2 2
Rear 7,14 m/s
2 2
Rear 6,62 m/s
2 2
Rear 3,99 m/s
2 2
GB | 37