Before Starting The Equipment; Attachment And Operation - Scheppach MFH3100-4BP.4 Traduction Du Manuel D'origine

Grasstrimmer: A = Front6,16 m/s
hv
Brush cutter: A = Front 2,39 m/s
hv
Hedge trimmer: A = Front 1,90 m/s
hv
Pole saw: A = Front 1,55 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this sign: m

7. Before starting the equipment

Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
1 Fuel and oil
m CAUTION!
The engine does not come with oil in it. There-
fore, ensure that you add 0,08 liters of oil before
starting it up. Use normal, multigrade oil (SAE30
/ 10W30). The oil level in the engine must be
checked each time before mowing. Fig. 63, 64
You will also need to fill in petrol, as this is also
not supplied upon delivery.
1 Fuel
Recommended fuels.
Normal petrol / Lead free max. 5% bioethanol
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Fuel, which have been left unused for a period of one
month or more, may clog the carburetor or result in the
engine foiling to operate property. Put remained fuel in-
to an airtight container and keep it in the dark and cool
room.
Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add fuel
to a machine with a running or hot engine. Take care
of fire.
34 GB
Rear 3,96 m/s
2 2
Rear 1,69 m/s
2 2
Rear 1,94 m/s
2 2
Rear 2,06 m/s
2 2

8. Attachment and operation

ASSEMBLY
When assembling this machine, please follow the inst-
ructions for assembly printed.
1 Assemble the handle on the machine. Fig. 2-3
• Install the front handle as shown on the image 2.
• Make sure that you align the pin with the hole. Tigh-
ten the screws only loosely before you have the
most comfortable working position set to the risers.
The front handle should be aligned as in pictures
2+3 shown, then tighten the screws.
2. Mounting the shaft. Fig. 4
• Pull out the locking pin (a) and press the lower part
of the shaft (b) downward until the locking pin en-
gages. The bolt (a) is in the right position when it is
fully seated in the bore.
• Lastly, tighten the knob (d) securely.
3. Assemble the safe guard. Fig. 5-7
• Fix the safe guard with hex key and wrench enc-
losed as stardard accessories for tighting the nuts
enough. Please see the below pictures showing.
m Warning! Never use the machine without the guard
assembled!
4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 8-9
• Release the nut.
Line up the two holes of flange and shield, use one
screw driver to hold the flange as below and turn the
socket wrench clockwise, the nut will be released.
• Fit the Nylon cutting head.
Remove another shield after release the nut. Still hold
the flange, take the Nylon cutting head on the shaft
and rotate counter-clockwise, the Nylon cutting head
is fitted. Fig. 19
• Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 10-12
Take the outer flange off after release the nut, then
put the blade (17), outer flange (17b), shield (17a)
and nut according to priority as below picture. Note
the blade rotation direction needs be same as below
picture. Use screw driver to hold flange and tighten
nut counter-clockwise, ensure the nut is tightened
enough.
• Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
m Warning!
Please make sure the cutting head has been assem-
bled correctly before use!
OPERATION
When working with the equipment as grass trimmer
and brush cutter, the appropriate plastic guard hood