Technical Data; Attachment And Operation - Scheppach TPX710 Traduction Des Instructions D'origine

6. Technical data

Hedge trimmer
Technical data
Cutting data hedge trimme
Cutting circle diameter
mm
Bar length mm
Cutting length mm
Max. cutting speed
max. min
-1
Telescope length min./
max. mm
Tilting range
Power unit
Engine V / Hz
Engine output W
Weight kg
Pole saw
Technical data
Data pole saw
Bar length mm
Cutting length mm
Guide bar typ
chain pitch
Saw chain type
Chain link thickness "
Max. cutting speed
max. min
-1
Telescope length min./
max. mm
Power unit
Motor V / Hz
Engine output W
Weight kg
Subject to technical changes!
concerning noise
Information
according to relevant standards:
Sound pressure L = 93 dB(A)
pA
Sound power L = 100 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration left hand A = 4,8 m/s
hv
Vibration right hand A = 3,5 m/s
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the places
that have to do with your safety with this sign: m
26 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
18
450
410
1540
1900-2500
0° - 120°
230-240 / 50
500
3,4
240
190
Oregon 552912
3/8"
91P033X
1,3
3800
1580 - 2150
230-240 / 50
710
3,1
emission measured
2
2

7. Attachment and operation

ATTENTION! Before working on the device - cleaning,
inspection, maintenance or other work - always turn off
the device and separate it from the power supply.
ASSEMBLY
Assembling the motor casing (Fig. 2)
• Open the qick acting lock (11) from the motor casing
(9).
• Insert the telescopic tube (6) into the casing's hol-
ding fixture.
• Close the casing's quick acting lock (11) again,
Attaching the shoulder strap, Fig. 3
Assembly and use:
• Fix the shoulder strap on the flap (4)
• By changing the adjuster, the length of the shoulder
strap can be altered. Adjust the length of the shoul-
der strap in such a way that it ensures a comfortable
working posture.
• Put the shoulder strap over your right shoulder.
• Carry the tool's motor on the right side of your body.
Never put the shoulder strap over your shoulder
and across your chest, but put it on one shoulder.
In this way, you will be able to quickly remove the
tool from your body in case of emergency.
m Warning! Use only original manufacturer's repla-
cement parts, accessories and attachments. Failure
to do so can cause poor performance, possible injury
and may void your warranty. Never use the machine
without the guard assembled!
Starting and stopping the telescopic hedge trim-
mer, (Fig. 4)
• Starting the device: First, press the safety switch (3)
on the back handle left, then the trigger (2). After
starting the motor, you can release the safety switch
(3).
• Stopping the device: Let go of the trigger (2).
Adjusting the telescopic tube (Fig. 5)
Disconnect the tool from the electricity supply
first!
• Open the locking handle (5) for length adjustment
• Adjust the telescopic tube (6) to the required length.
• After the adjustment, close the locking handle (5)
again, so that the length adjustment is secure.
Adjusting the motor head (Fig.6)
Disconnect the tool from the electricity supply
first!
Angle adjustment A
• Press the button (10) for the angle adjustment on
both sides and rotate the head to the required positi-
on (from 0° to 120°). Make sure that the motor head
clicks into place again.