Fixed Installation; Aligning The Spotlights; Power Supply; Operation - IMG STAGELINE PARL-45SET Mode D'emploi

4.2 Fixed installation

For fixed installation to a wall or ceiling, fasten the
two mounting brackets (c) in an appropriate way at
a suitable location. Use the knurled screws sup-
plied (d) to fasten the controller to the brackets
(fig. 4).

4.3 Aligning the spotlights

To align the spotlights, loosen the corresponding
setscrews (1 and 2) and turn and tilt the spotlight
into the direction desired, making sure that the
cables are neither squeezed nor stretched. Then
retighten the screws.
On the upper side of the controller, additional
threaded holes are available so that the spotlights
can also be mounted there: Remove the screws (1)
of the spotlights and fasten the spotlights in the
same way on the upper side of the controller, using
the rubber washers and the screws.

4.4 Power supply

Use the mains cable supplied to connect the mains
jack (4) of the spotlight set to a mains socket
(230 V~/ 50 Hz). The unit will be switched on. The
display (11) will indicate the operating mode most
recently selected and will extinguish after 30 sec.
Then only a dot will light up to indicate that the spot-
light set is switched on. When a control button (12)
is pressed, the display will light up for 30 sec. again.
WARNING To prevent damage to your eyes,
never look directly into the light
source for a longer period of time.
Please note that fast light changes
may trigger epileptic seizures with
photosensitive persons or persons
with epilepsy!
If multiple spotlight sets PARL-SET45 are used,
connect the jack POWER OUT (5) of the first unit to
the mains jack (4) of the second unit by means of a
mains cable with 3-pin IEC plug and 3-pin IEC
inline jack (e. g. AAC-170 / SW from the MONACOR
product line). Then connect the second unit to the
third unit, etc. until all units are connected in a
chain. Up to 20 units may be connected in this way.
The jack POWER OUT may also be used to pro-
vide power to other (light effect) units. The current
load of the jacks POWER IN and POWER OUT,
however, must not exceed 6.3 A; otherwise, over-
load may result in short circuit and fire. The jacks
POWER IN and POWER OUT are not protected by
the fuse (3).
12
5

Operation

The control buttons MENU, UP, DOWN and
ENTER (12) are used to select the operating mode
and various functions. Please refer to the menu
structure on page 15 for an overview of how to
select the modes and functions.

5.1 Stand-alone mode

5.1.1 Colour spotlights and stroboscope

In the stand-alone mode, the spotlights constantly
emit an adjustable colour. The stroboscopic func-
tion may be activated in addition.
1) Press the button MENU repeatedly until
appears on the display.
2) Press the button ENTER. The display shows
for the colour red and a value between 00 and
08 to indicate its brightness.
3) Use the buttons UP and DOWN to set the
brightness desired for the colour red.
4) Press the button ENTER repeatedly to select
the colours green ( ) and blue ( ) and the
stroboscopic function ( ) one after the other.
Then the selection cycle starts again with
, etc. Set the brightness for each colour and,
if required, the stroboscopic frequency (
no stroboscope,
Hint: Setting the brightness of the colours red, green
and blue will not only change their brightness but also
their hue in a colour mix. Therefore, first set the colour
that is to dominate to the brightness desired and then
add the other two colours. If the intended colour mix is
white, first set the brightness of the colour green,
because green appears to be the brightest colour to the
human eye. Then add red to get yellow and finally add
blue to get white.
5) To save the setting, press the button ENTER
until appears on the display.
5.1.2 Colour change programs
and running light programs
The unit provides 12 automatic light programs with
adjustable speed:
1) Press the button MENU repeatedly until
a number between 01 and 12 appear on the dis-
play. The number indicates the program num-
ber.
2) Use the buttons UP and DOWN to select a light
program.
3) To change the speed, press the button ENTER
repeatedly until
and 08 appear on the display. Use the buttons
UP and DOWN to set the speed. To switch off
the spotlight, select
= slow, ... = fast).
and a number between 00
.
,
=
and