Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
workpiece. Pay attention to the splitting
wedge thickness, see the numbers pun-
ched on the splitting wedge. The splitting
wedge may not be thinner than the saw
blade body and not thicker than its saw kerf
width.
•
Lower the covering hood on the workpiece
during each operation
•
The covering hood must be horizontal
during each operation
•
During longitudinal cutting of small workpi-
eces – smaller than 120 mm - use the slide
rod without fail. The slide rod must be used
to prevent working with the hands in the
vicinity of the saw blade.
•
Switch the machine off to rectify faults or to
remove jammed wood pieces. Disconnect
the power plug.
•
Replace the table insert in case of lined
saw crevices. Disconnect the power
plug.
•
Conversion-, adjustment-, measurement-
and cleaning jobs are to be performed only
after the motor is switched off. Disconnect
the power plug.
•
Before start-up, the machine should be
connected to a vacuum cleaner with a
flexible, non-inflammable suction pipe.
The vacuum cleaner must get activated
automatically when the circular table saw is
switched on.
•
Switch the motor off while leaving the work-
place. Disconnect the power plug.
Proper use according to manufacturer´s instructions m
The machine corresponds to the applicable
EC Machine Directive.
•
The machine has a workplace which is
D GB
located before the machine at the left of the
machine table.
•
To prevent accidents, the working- and
surrounding area of the machine must be
free of disturbing foreign bodies.
•
In principle, the workpieces to be pro-
cessed must be free of foreign bodies such
as nails or screws.
•
Before start-up, the machine should be
connected to a vacuum cleaner with a
flexible, non-inflammable suction pipe. The
grading must be activated automatically
when the circular table saw is switched
on. The flow speed at the vacuum suction
nozzle must be 20 m/s.
The activation automation is available as special
accessory.
Type ALV 2: Art. No. 7910 4010, 230 V/50 Hz
On switching the machine on, the vacuum
cleaner starts automatically after a lag of 2-3
seconds. This prevents overloading of the
internal fuse. On switching the machine off, the
vacuum cleaner is deactivated automatically
after a lag of 3-4 seconds. The residual dust is
removed this way, as required by the Hazardous
Substances Ordinance. This saves power and
reduces the noise. The vacuum cleaner runs
only when the machine is operated. For jobs in
the commercial area, a suitable and approved
dust filter must be used. Do not connect or dis-
connect vacuum cleaner or dust filter when the
machine is in operation.
•
The machine is designed exclusively for
processing wood and similar substances.
Only original tools and accessories are to
be used. Depending on the section- and
wood type (solid wood, plywood or particle
boards) use the required saw blade accor-
ding to Standard EN 847-1. Observe the
tool special accessories at the end of this
operating instructions manual.
•
Even if there is a slight position change,
disconnect the machine from any external
power source. Reconnect the machine
properly to the mains power supply again
before restart.
•
Only electricians should be allowed to per-
form installation, repair and maintenance
jobs on the electrical equipment.
•
All protection and safety devices must be
reinstalled immediately after the repair and
maintenance jobs are over.
•
Do not expose electrical tools to rain.
•
Do not use electrical tools in humid and wet
environments.
•
Ensure good illumination of the work area.
•
Do not use electrical tools at places where
there is risk of fire or explosion.
•
Avoid body contact with earthed parts (e.g.,
pipes, radiators, electric stoves, cooling
devices).
•
Unused electric tools should be stored at
a dry, elevated or sealed place outside the
reach of children.
•
Do not pull the cable to disconnect the po-
wer plug from the mains socket. Protect the
cable from heat, oil and sharp edges.
•
Use clamping devices, slide handles or a
slide rod to hold the workpiece in place.
It can be held safer this way than with the
hand.
•
Keep the handles dry, clean and free of oil
and grease.
•
While inserting the power plug into the
mains socket, ensure that the switch is off.
•
Use the machine only if it is in a flawless
condition technically, and only after lear-
ning about its proper and safe use, as well
as about the risks involved, complying with
the operating instructions! Get faults that
compromise safety in particular rectified,
immediately
•
The safety-, work- and maintenance speci-
fications of the manufacturer as well as the
dimensions specified in the technical data
must also be observed.
•
The appropriate accident prevention regula-
tions and the other generally acknowledged
safety rules must be observed.
•
The machine is to be used, evaluated or
repaired only by persons who are familiar
with the working of the machine, and are
informed about the involved risks. Unautho-
rized changes in the machine will release
the manufacturer from any liability for the
damages resulting there from.
•
The machine may be used only with original
accessories and original tools of the manu-
facturer.
•
Any use going beyond this will be interpre-
ted as improper. The manufacturer will not
be liable for damages resulting there from;
the risk will be borne by the user alone.
The machine is designed on the basis of
the latest technology and the recognized
safety-related rules. Nevertheless, individual
residual risks may occur when performing
jobs on the machine.
•
Risk of physical injury to fingers and hands
from the rotating tool, if the workpiece is
not guided properly.
•
Risk of injury from the departing workpiece
during improper holding and guidance,
such as performing jobs without stop.
•
Risk to health from noise. When working,
the permissible noise level is exceeded.
Wear personal safety equipment such as
ear guards without fail.
20
•
Use only an approved and appropriately
marked extension cable in the open.
•
Do not use electric tools in which the switch
cannot be activated and deactivated
•
Circular saws should not be used for split-
ting (groove ending in the tool).
•
Use only saw blades whose maximum
permissible speed is not less than the ma-
ximum spindle rotation speed of the circular
table saw and the material to be cut.
•
When transporting the machine, use only
transportation equipment and never use
protective devices for handling or transport.
•
During transportation, the topmost section
of the saw blade must be covered, e.g.,
with the protective device. Purchase acces-
sories only from your specialised dealer.
•
The circuit breaker (16A) with RCD module
(30mA) and overvoltage protection devices
shall be installed for supplying electric
power to this machine, in order to protect
people against electrical shock due to indi-
rect shock. If the machine is connected in
TN system, Test 2 according to EN 60204-1
is to be verified under final installation.
•
Physical injuries due to defective saw
blade. Check the saw blade regularly and
before each use for physical integrity.
•
Risk from power, the use of improper elec-
trical connecting cables.
•
When using special accessories, the at-
tached operating instructions must be read
carefully and observed.
•
Nevertheless, apparent residual risks may
occur despite taking all precautions.
•
Residual risks can be minimized if the safe-
ty instructions and the "Proper use accor-
ding to manufacturer's instructions" as well
the operating instructions are observed on
the whole.
Publicité
Table des Matières
