Accessoires - Scheppach Bestcombi 7.0 Traduction Du Manuel D'origine

ON and OFF switch Fig. A 8
Each ON switch allows the start of its own
function
Set master switch (T) in the milling mode (see
icons on the switch box)
Green button - Activate
Red button - Deactivate
In case of danger, press lateral Emergency-Stop
switch
Caution: To start a function, one must unlock the
stop switch without fail.
Slide carriage Fig. B 7
The slide carriage is fully installed.
To unlock, pull out the button (5) laterally on the
table, rotate ¼ turn to the right and re-engage.
Delivery table Fig. B 8
Install table (6) if necessary, laterally with 2
tommy screws.
Slide carriage with clamping device and
angle setting Fig. 8
Introduce angle stop (7) into the groove of the
slide table with the guide bar and tighten with
the turning handle (9).
For angle settings, loosen the tommy screws
(10), set angle and tighten again.
Place the tool clamp (11) in the opened state
over the workpiece, tighten the clamping screw
(12) and clamp the workpiece with the eccentric
lever (13).
Installation and operation of the jointing and
planing machine
3.0 Jointer and planer (C)
A Adjustable jointing table
B Jointing support table
C Adjusting wheel for cutting depth
D Jointing stop
E Planer shaft protection
F Vacuum suction hood
G Height adjustment wheel of planing table
H Planing table
I ON and OFF switch
Caution: Disconnect the power plug before
performing adjustment and retrofitting jobs.
Cross-table with telescopic arm ..............................................................................Art. Nr. 1902103701
Bend milling stop .......................................................................................................Art. Nr. 1902403702
Pin cutting device ...................................................................................................... Art.Nr. 3300454742
HS-Planer knife .......................................................................................................... Art.Nr. 3304000004
Swivel plates of HS-planer knife .............................................................................. Art.Nr. 3304200023
Knife holder ................................................................................................................ Art.Nr. 3304300033
Jointing Figure. C1
The vacuum suction hood (F) is installed perma-
nently under the jointing table (B)
Plug in vacuum suction hose (D 100 mm)
Detach the feed rollers with the help of lever (1)
to avoid unnecessary wear and tear
Setting the jointing stop Fig. C2 and C3
Remove cover plate (2) between jointing table
and milling table
Install guide section (3) with 2 Allen screws (3)
Insert stop guide (5) and tighten with tommy
screw (6)
Insert the stop bar (7) in the stop guide (5), with
carriage bolt
And fasten tommy screw (8)
By loosening the tommy screw (6) the stop
can be moved along the entire width
of the jointing table
The stop rail can be inclined up to 45°, to do this,
loosen the clamping screw (8), adjust angle and
re-tighten
Caution! Tighten all the parts well again after
each setting.
Setting the planer shaft cover
The planer shaft cover must always be set such
that it covers the section of the planing shaft that
is not being used.
Caution: Use slide rod.
For flat workpieces, adjust the height of the co-
ver such that the workpiece can be slided under
the guard.
For strong workpieces that cannot be covered,
use the slide handle.
Setting the cutting depth Fig. C4
The handle (6) can be used to change the height
of the adjustable jointing table 1 increment = 1
mm
The cutting depth can be read on the scale (7)
Planing
Conversion from jointer to planer Fig. C5
and C6
Remove the jointing stop
Detach the clamping lever (8) under the adjus-
table jointing table
Tilt table laterally in the outer direction
Detach the clamping lever (8) under the jointing
table and tilt the table with the planer shaft cover
laterally in the outer direction
Fold the vacuum suction hood (F) upwards and

Accessoires

23
engage
Connect the vacuum cleaner hose.
Setting of table height Fig. C6
Set the planing table (H) with the height adjust-
ment wheel (G) to the workpiece size
with the help of the scale (9) and clamp tightly
with the tommy screw (10).
Cutting depth 1 rotation = 3mm
Automatic wood feed Fig. C7
Switch on feed roller with lever (11)
In case of danger, switch the Emergency-Stop
switch (12)
ON and OFF Fig. C8
Set machine to planing on the switchbox (Fig.
1.0 A) and on the
Feed side during planing
Green button (13) - Activate
Red button (14) - Deactivate
Planer knife replacement Fig.C9
Caution: Disconnect the power plug before
performing adjustment and retrofitting jobs.
Fold planer knife guard down
Loosen 5 clamping screws (15) and remove
planer knife (16) with holder (17)
Clean all the parts, insert a new planer knife
with holder
Setting the knife
Set adjustable jointing table to 2 mm cutting
thickness
Mount 2 well jointed wood strips on the pick-up
table
Turn the planer shaft to bring the cutter of the
knife to its highest position
Set the height with the 2 adjusting screws (18)
and tighten the clamping screws.
Checking settings Fig. C10 and C11
Place a jointed bar (19) on the pick-up table and
mark the position (a).
By turning the planer shaft, the cutting edge of
the knife should move the bar (19) by 2-3 mm.
Position (b)
This test must be conducted for each knife on
the left and right sides.
A smooth and trouble-free planing is guaranteed
if the execution is accurate.
D GB