GB
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a plas-
tic cover to protect it from dirt and moisture.
Read the instruction manual each time before oper-
ating the machine and carefully follow its information.
The machine can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
In addition to the safety notices contained in this op-
erating manual and the particular instructions for your
country, the generally recognised technical regula-
tions for the operation of identical devices must be
complied with.
36 І 212
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
2. Device description
1.
Chain
2. Guide bar
3. Hand Guard / Chain Brake Lever
4.
Fuel pump (Primer)
5. Throttle
6. Rear Handle
7.
Safety locking button (throttle lock)
8. Starter grip
9.
Air filter cover
10. Fan housing with starting assembly
11. Oil tank cap
12. Front grip (tubular handle)
13. Fuel tank cap
14. Choke switch
15. I/STOP-switch (short-circuit switch)
16. Retaining nut- Sprocket guard
17. Sprocket guard
18. Exhaust muffler
19. Carabiner or rope attachment point
20. Chain catch
21. Claw Stop
22. Allen wrench
23. Combination wrench
24. Chain protection cover
3. Scope of delivery
Chain
(1x)
Chainsaw
(1x)
Guide bar
(1x)
Chain protection cover
(1x)
universal wrench
(1x)
Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
If possible, store the packaging until the warranty pe-
riod has expired.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
4. Intended use
This machine is a particulary light and easy to handle
chain saw with overhead mounted handle. This chain
saw is designed especially for tree care and surgery.
These chainsaws may therefore only be operated by
"Chainsaw operators with additional training for work
using raised platforms or ladder platforms and/or us-
ing rope climbing techniques".