Performing Time Correction Manually (Tcr) - Alpine IVA-W205 Mode D'emploi

8
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of FREQ., then select the cut-off frequency
(crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
Adjusting the Level
Touch [ ] or [ ] of LEVEL, then adjust the HPF or LPF level.
Adjusting the Slope
Touch [ ] or [ ] of SLOPE, then adjust the HPF or LPF
slope.
9
Touch [RETURN] to return to the previous screen.
• When the speaker is set to the "OFF" mode, the X-OVER for that
speaker cannot be set. Refer to "Setting the Speakers" (page 43).
• Check the playback frequencies of the connected speakers before
adjusting.
• In order to protect the speakers, there is no OFF setting for the
subwoofer low pass filter (the slope remains the same).
• The HPF cannot be set SLOPE to OFF if Tweeter (TW) is selected
for FRONT1 . Or, only the subwoofer is adjustable if STEREO is
selected for the subwoofer.
Performing Time Correction Manually
(TCR)
Because of the particular conditions inside the vehicle, there can be
major differences in the distances between the various speakers and the
listening position. It is possible to calculate the optimum correction
values and eliminate the time error at the listening position yourself
using this function.
1
Check that Defeat mode is off (page 25).
2
Sit in the listening position (the driver's seat, for
example) and measure the distance (in meters)
between your head and the various speakers.
3
Calculate the difference in distance between the
farthest speaker and the other speakers.
L = (distance of farthest speaker)
– (distance of other speakers)
4
Divide the distances calculated for the different
speakers by the speed of sound (343 m/s
temperature 20°C).
This value is the time correction value for the various
speakers.
Concrete examples
Calculating the time correction value for the front left speaker on
the diagram below.
Conditions:
Distance between farthest speaker and listening position:
2.25 m (88-3/4")
Distance between front left speaker and listening position:
0.5 m (20")
Calculation:
L = 2.25 m (88-3/4") – 0.5 m (20")= 1.75 m (68-3/4")
Compensation time = 1.75 ÷ 343 x 1000 = 5.1 (ms)
44
-EN
In other words, setting the time correction value for the front left
speaker to 5.1 (ms) sets a virtual distance matching the
distance to the farthest speaker.
0.5m
2.25m
The sound is uneven because
the distance between the
listening position and the
different speakers is
different.
The difference in the distance
between the front left and
rear right speakers is 1.75
meters (68-3/4").
5
Touch [SETUP] on the main source screen.
The SETUP selection screen appears.
6
Touch [AUDIO].
The AUDIO SETUP screen appears.
7
Touch [ ] of A.PROC.
The A.PROCESSOR list screen is displayed.
8
Touch [ ] or [ ] of T.CORR.
Select L/R or L+R.
L/R: Different adjustment values can be set for the left and
right channels.
L+R: Sets the same adjustment values for the left and right
channels.
9
Touch [ ] of T.CORR.
The T.CORR adjustment screen appears.
10
Adjust the time correction value (0.00 ~ 20.00ms) of
a desired speaker by touching the respective [ ] or
[ ] button (1 step = 0.05ms).
11
Touch [RETURN] to return to the previous screen.
• When the speaker is set to the "OFF" mode, the TCR for that
speaker cannot be set. Refer to "Setting the Speakers" (page 43).
• The adjustment value for FRONT2 (Speakers) which is adjusted in
time correction, is also applied to the front speakers in "Setting Bass
Focus" (page 46).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
5.1ms
Time correction eliminates
the difference between the
time required for the sound
from the different speakers to
reach the listening position.
Setting the time correction of
the front left speaker to 5.1
ms makes it possible to
coordinate the distance from
the listening position to the
speaker.