Aux In Mode; Setting The Clock; Setting The Alarm; Setting The Alarm Clock - PERFECTPRO Slim 2 Manuel De L'utilisateur

AUX IN MODE

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (not included with
this radio).
1. Connect an audio SOURCE to the Aux In socket on the backside of the radio.
2. Press the SOURCE button to select AUX input. Display will show "AUX IN".
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the AUX-IN socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal* from the AUX input jack for a period over 15 minutes, the unit will automatically
switch to standby mode. The operation indicator and the LCD will go off in such case.
Pressing the ON/OFF button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.

SETTING THE CLOCK

The clock can only be set when the radio is in standby mode. If no buttons are pressed
for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the TUNING/SEEK knob for 12 seconds until the hour digits flash
on the display.
2. Rotate the TUNING/SEEK knob to set the hour.
Press the TUNING/SEEK knob to confirm, the minute digits flash.
3.
4. Rotate the TUNING/SEEK knob to set the minute.
5. Press the TUNING/SEEK knob to confirm, the day flashes on the display.
6. Rotate the TUNING/SEEK knob to set the current day.
7. Press the TUNING/SEEK knob to confirm, the month flashes.
8. Rotate the TUNING/SEEK knob to set the current month.
9. Press the TUNING/SEEK knob to confirm, the year will then flash on the display.
10. Rotate the TUNING/SEEK knob to set the current year.
11. Press the TUNING/SEEK knob to confirm, "SYNCLOCK ON" flashes.
12. Rotary the TUNING/SEEK knob to select "SYNCLOCK ON" or "SYNCLOCK OFF".
13. Press the TUNING/SEEK knob to confirm and finish the clock setting.
15

SETTING THE ALARM

The alarm can only be set when the radio is in standby mode. If no buttons are pressed
for 10 seconds, the radio will exit the alarm setup and the setting is cancelled. Or press
the MENU button during alarm setup, the radio will also return to standby mode without
saving the adjusted alarm settings.

Setting the alarm clock

1. Press the MENU button for about 3 seconds, the display shows "ALARM SET" and
the hour digits flash on the display.
2. Rotate the TUNING/SEEK knob to set the hour.
3. Press the TUNING/SEEK knob to confirm. The minute digits flash.
4. Rotate the TUNING/SEEK knob to set the minute.
5. Press the TUNING/SEEK knob to confirm.
6. The display will then show "ALARM SOURCE". You may choose "BUZZER", "DAB"
or "FM RADIO". Rotate the TUNING/SEEK knob to select. If "DAB" is selected, the
last listened station will be played when the alarm fires.
7. Press the TUNING/SEEK knob to confirm.
8. The display will then show "VOL XX". Rotate the TUNING/SEEK knob to change
the alarm volume.
9. Press the TUNING/SEEK knob button to confirm.

Switching on/ off the alarm

To switch the alarm on, press the MENU button briefly. The alarm icon will be shown
at the top left corner. To switch the alarm off, press the MENU button briefly again. The
alarm icon will be disappeared.
Press the ON/OFF button to turn off the alarm when it is firing.

LOUDNESS

The Loudness function enables to get compensation on lower and higher frequency.
The effect will be more audible when the radio is in a lower volume level (Dynamic
Loudness).
1. Press the LOUDNESS button to enable the loudness, the display shows
"Loudness On".
2. Press the LOUDNESS button again to disable the loudness, the display shows
"Loudness Off".
GB
16