Manual Tuning; Rds Station Service - Fm; Preset Stations; Storing Preset Stations - PERFECTPRO Slim 1 Manuel De L'utilisateur

Manual tuning

1. Press the POWER button to turn on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Rotate the TUNING/SEEK knob to reach the required FM station.
The radio will change the frequency in steps of 50 kHz.
4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a station
of sufficient signal strength with RDS information present, the display may change
to show the station name.
5. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.
RDS station service – FM
RDS (Radio Data System) is an information system which inaudible digital information is
transmitted in addition to the normal FM radio programme. When the radio is receiving a
RDS station and the reception strength is sufficient, the station name will appear in the
display. It may take some time before the RDS information is available.
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the INFO
button to cycle through the information. This will only function if the reception level is
sufficient and clear.
a. Radio text (RT) Displays the message about the station being listened
to as ticker text.
b. Program type (PTY) Displays the type of station being listened to, e.g. Pop,
Classic, News, etc.
c. Frequency Displays the frequency of the station being listened to.
d. Time & date Displays the current time (24 hour clock) and date.
e. Signal level Displays the signal strength.

PRESET STATIONS

Storing preset stations

There are 5 memory presets in the radio for FM. Presets are remembered by the radio
in the event of a power failure.
1. Press the POWER button to turn on the radio.
Press the SOURCE button to select the desired waveband.
2.
3. Tune to the required station.
4. Press and hold the required Preset button and shows for example "P1 Saved".
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written by following the above
procedure.
7

Recalling preset stations

1. Press the POWER button to turn on the radio.
2. Press the SOURCE button to select the desired waveband.
3. Briefly Press the required Preset button, the display will show, e.g. "108.00 P1", on
the LCD.

AUX IN MODE

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (not included with
this radio).
1. Connect an audio SOURCE to the Aux In socket in rare side of the radio.
2. Press the SOURCE button to select AUX input and the AUX icon will be lightened.
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the AUX-IN socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal from the AUX input jack for a period over 15 minutes, the unit will automatically
switch to standby mode. The operation indicator and the LCD will go off in such case.
Pressing the POWER button will wake up the unit.

SETTING THE CLOCK

The clock can only be set when the radio is in standby mode. If no buttons are pressed
for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the TUNING/SEEK knob for 12 seconds until the hour digits flash
on the display.
2. Rotate the TUNING/SEEK knob to set the hour.
3. Press the TUNING/SEEK knob to confirm, the minute digits flash.
4. Rotate the TUNING/SEEK knob to set the minute.
5. Press the TUNING/SEEK knob to confirm, "CT ON" flashes.
6. Rotary the TUNING/SEEK knob to select "CT ON" or "CT OFF".
7. Press the TUNING/SEEK knob to confirm and finish the clock setting.
RDS time synchronisation
Some RDS stations transmit a time signal. If reception is good and you have selected
the "CT ON" option during the time setting, the time will be automatically updated (flashes
on the display). Time synchronisation can take several minutes. The automatic time
setting is always activated when the radio is switched from standby to FM broadcasting
and receives a RDS station.
GB
8