Operat Ion - Rem Ot E Cont Rol Handset - Enduro EM303+ Manuel D'utilisateur

OPERATI ON – REM OTE CON TROL H AN D SET
The rem ot e cont rol handset ( 31) is power ed by one PP3 9Volt bat t ery, and is act ivat ed by m oving t he slide
swit ch t o " On" - I ( Fig. 5A) . Once act ivat ed t he green LED ( Fig. 5H) will illum inat e and t he direct ional cont rols
can now be used.
Fig. 5
A. Slide sw it ch ( " Off" –O and " On" - I )
B. Caravan forwards ( bot h wheels rot at e in for wards direct ion)
C. Caravan reverse ( bot h wheels rot at e in rev er se dir ect ion)
D. Caravan left forwards ( right wheel rot at es in forwards direct ion)
E. Caravan right forwards ( left w heel rot at es in forwards direct ion)
F. Caravan left reverse ( right w heel rot at es in reverse direct ion)
G. Caravan right r everse ( left w heel rot at es in r everse direct ion)
H. Green LED: reflect s st at us of t he r em ot e cont rol and carav an m anoeuvr ing syst em
I . Red over load LED: Am p over load prot ect ion is act ivat ed. Wait about 60 seconds and t ry again
J. Blue 9V bat t er y LED: The int ernal 9V bat t er y of handset is near em pt y and needs t o be replaced
K. Blue bat t ery v olt age LED: Caravan bat t ery volt age t oo low or t oo high
When you driv e st raight forw ards or reverse ( press but t on B or C) , it is also possible t o adj ust t he direct ion by
addit ional pressing but t on D or E ( when driving forwards) or but t on F or G ( when dr iving reverse) .
I n addit ion, t he 'right forward' ( E) and 'left reverse' ( F) but t ons or 'left forward' ( D) and 'right rev erse' ( G)
but t ons m ay be pressed at t he sam e t im e t o t urn t he carav an around on it s own ax is w it hout m oving forward or
backward ( t his funct ion j ust can work under t he " single- ax le funct ion" ) .
When you swit ch wit hin 2 seconds from forw ard driving t o r everse driving ( and t he ot her way around) , a sm all
delay of 1 second will appear t o prot ect t he elect ronics and t he m ot or s.
Th e slide sw it ch ( Fig. 5 A) a lso a ct s a s a n "Em e r ge n cy st op".
Th e r e m ot e h a n d se t sw it ch e s off:
 Aft er 3 m inut es, if no but t on is pressed: Aft er 2 m inut es t he buzzer will beep for 5 t im es wit h a r epet it ion
aft er 3 m inut es. Than t he sy st em swit ches in t he " st and- by" m odes.

Aft er 6 m inut es, if one of t he m ovem ent but t ons is per m anent ly held down: Aft er 5 m inut es t he buzzer will
beep for 5 t im es wit h a r epet it ion aft er 6 m inut es. Than t he syst em sw it ches in t he " st and- by" m odes.
The green LED goes off and t he rem ot e cont rol handset is in t he " st and- by" m odes which m eans t hat t here
always w ill be used som e cur rent w hich causes t he bat t ery t o go down. So always m ake sure t he rem ot e
cont rol handset is t ur ned off by t he slide sw it ch.
To react ivat e t he rem ot e cont rol, m ove slide swit ch t o " Off" –O and t hen back t o " On" - I aft er approxim at ely 1
second.
Er r or m e ssa ge s via t h e r e m ot e con t r ol h a n dse t :
Error m essages of t he EN
handset by t he green LED ( Fig. 5H) , t he err or m essage LED's ( Fig. 5I , 5J & 5K) and a buzzer signal:

Green LED ( Fig. 5H) off, no buzzer: r em ot e cont rol handset is t ur ned off and also syst em is not act ivat ed

Green LED ( Fig. 5H) cont inue on, no buzzer: rem ot e cont rol handset is t ur ned on and syst em is act ivat ed
and ready t o use.

Green LED ( Fig. 5H) is blink ing, no buzzer: no com m unicat ion bet w een handset and cont rol unit . This could
be because of t oo m uch dist ance bet w een r em ot e control handset and cont rol unit , or t he bat t ery isolat ion
swit ch for m anoeuvring syst em is not t urned on or t hat t here is a dist or t ion signal dist urbing t he
com m unicat ion. As soon as connect ion is good again t he gr een LED w ill be cont inue on and t he syst em is
ready t o use.

Blue bat t ery v olt age LED ( Fig. 5K) is blinking in com binat ion wit h buzzer ( 2 t im es blink ing, break , 2 t im es
blinking, break et c.) : Bat t ery volt age t oo low ( < 10V) . Bat t ery needs t o be recharged.

Blue bat t ery v olt age LED ( Fig. 5K) is blinking in com binat ion wit h buzzer ( 4 t im es blink ing, break , 4 t im es
blinking, break et c.) : Bat t ery Volt age t oo high ( over charged) . Try t o discharge t he bat t ery by t urning on a
user ( for exam ple a lam p or wat er - pum p) .

Red over load LED ( Fig. 5I ) is blinking in com binat ion wit h buzzer ( 6 t im es blinking, break , 6 t im es blink ing,
break et c.) : Am p overload pr ot ect ion is act ivat ed. Wait about 60 seconds and t ry again.

Blue 9V bat t er y LED ( Fig. 5J) is blink ing, no buzzer: The int ernal 9V bat t ery is near em pt y and needs t o be
replaced.
Ch a n gin g ba t t e r ie s in t h e r e m ot e con t r ol:
When t he bat t ery is em pt y ( blue 9V bat t er y LED ( Fig. 5J) is blink ing) , it needs t o be r eplaced.

Open t he rear cover of t he handset ( Fig. 7A) .

Take out t he dead/ old bat t er y and dispose in t he appropriat e way.

I nst all a new r eplacem ent bat t ery ( Fig. 7.1) . Make sure t o use a leak proof PP3 ( 9Volt ) bat t ery ( No claim s
under guarant ee can be considered for dam age caused by leak ing bat t eries) .
 Close t he rear cover again.
® +
EM303 m anoeuvring sy st em w ill be com m unicat ed via t he r em ot e cont rol
D URO
EN
D URO
® +
EM303 33
+
Ref: EM303 - UM- TKI - 0116- Rev.A.