Information About The Indoor Unit; Deleting All Pictures; Reset; Coding The Bell Receiver - M-E Vistadoor Vistus VDV-907 Mode D'emploi

VDV-907 | ENGLISH
On the next page you will find the links to the
Android and iOS app, as well as further infor-
mation on operating the app.

Information about the indoor unit

Touch the information symbol. The operating
voltage of the indoor unit is displayed here in
volts. It should be between 15V and 15.5V. The
IP address of the indoor unit is also displayed.

Deleting all pictures

Touch the dustbin symbol if you want to de-
lete all saved pictures. Touch the green high-
lighted field there and confirm the following
dialogue with "Ok" to delete all pictures or
touch "Cancel" to cancel the deletion process.
GB

Reset

Touch Reset to reset the indoor unit to facto-
ry settings, e.g. if you have forgotten the ac-
cess data for the app.
Touch the green button and confirm the reset
by tapping "Ok" in the following dialogue.
Please note that photos are not deleted by a
reset.

Coding the BELL receiver

Tap on the BELL symbol to access the set-
tings menu for the radio chime. Put the recei-
ver into learning mode by pressing the code
button until the receiver beeps briefly and
then tap one of the letters on the monitor.
The receiver plays a melody and is ready to
be learned.

Setting the melody of the radio chime

Tap on the BELL symbol to enter the settings
menu for the radio chime. There you have the
option of deactivating the integrated radio
module and changing the melody of the ra-
dio chime. Tap on a letter, the taught-in radio
chime plays the corresponding melody. This
melody is immediately saved and you can
exit this menu using the back arrow.

Coding the CUVEO receiver

Put the receiver in the learning mode (press
the button on the receiver until the LED on
the receiver flashes) and activate the monitor
by tapping on the touch-active surface. then
tap on the light symbol. If the light symbol is
not displayed, check whether it is activated in
the basic settings (B5).
45
Changing the coding of the radio protocol
(CUVEO and BELL)
If the CUVEO receiver and/or the BELL recei-
ver activate for no reason, another transmit-
ter in the vicinity could be transmitting the
same code. To change the code, proceed as
follows: The monitor must be in standby.
Hold a finger on the mute button (approx.
7 seconds) until the key and mouth symbols
light up.
Then all receivers (CUVEO and BELL) must
be relearned.

TECHNICAL DATA

Operating voltage: 15Volt DC
Power consumption: 270 ± 50mA
Frequency WLAN: 2.4GHz; <100mW
Frequency BELL: 434MHz; <10mW
Temperature range: 0-50°C
Max. humidity: 85 %
Screen diagonal: 178mm
Monitor resolution: 1024x600
Dimensions: 220x160x28mm (W x H x D)
46
ENGLISH | VDV-907

NOTES

Exposure to strong static, electric or high-fre-
quency fields (discharges, mobile phones, ra-
dio equipment, mobile phones, microwaves)
may impair the function of the equipment
(the appliance).

Cleaning and care

Disconnect mains operated units from the
mains (pull out the plug) before cleaning. The
surface of the housing can be cleaned with a
soft cloth moistened with soapy water. Do
not use abrasive cleaners or chemicals. Loo-
sen dust deposits on ventilation slots only
with a brush and, if necessary, vacuum with a
hoover. Do not hold the suction nozzle di-
rectly against the unit.

Legal principles

1. As the operator or user of the video door
unit, please observe the regulations and
legal principles of your country for the use
of surveillance devices with regard to
personal rights and data protection!
2. In many countries, video images and/or
speech may only be transmitted after a
visitor has rung the doorbell.
GB