Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
GRAPHIC SWITCHER II™
10-4. COMMANDS AND RESPONSES TABLE
The following table resumes all of the commands that are recognized as valid and the responses that will be returned to the
control device.
ASCII
RESPONSE
COMMAND
FRONT PANEL COMMANDS
C
CH
c
ch
G
TAKE
Z
FRZ
z
frz
M
STO
m
sto
R
REC
r
rec
H
HP
h
hp
V
VP
v
vp
W
HW
w
hw
S
VS
s
vs
INPUT COMMANDS
PC
PCH
PE
PEN
PL
PLD
PR
PRGB
PI
PSTD
ys
ISHR
OUTPUT COMMANDS
F
OFMT
fm
OSYN
fp
osyn
fs
SCRN
pm
PAT
pp
pat
REFR
XR
ur
ADJR
ug
ADJG
ub
ADJB
NOTE:
Rd = Read only command.
COMMAND
DESCRIPTION
MAIN selected input (read only).
Input pre-selection (PREVIEW).
TAKE (transition).
FREEZE MAIN.
FREEZE PREVIEW.
STORE (MAIN).
STORE (PREVIEW).
RECALL (MAIN).
RECALL (PREVIEW).
Horizontal position (MAIN).
Horizontal position (PREVIEW).
Vertical position (MAIN).
Vertical position (PREVIEW).
Horizontal size (MAIN).
Horizontal size (PREVIEW).
Vertical size (MAIN).
Vertical size (PREVIEW).
Input selection for adjustment.
Input disabling (works with PC)
H sync load selection (works with PC). Rd/Wr
RGB input type selection (works with
PC command).
Input standard selection (works with
PC command).
Composite or S.VIDEO mode
selection.
Output formats selection.
MAIN output sync selection.
PREVIEW output sync selection.
Type of screen selection
MAIN test pattern selection.
PREVIEW test pattern selection.
Input synchronization selection.
Red level adjustment.
Green level adjustment.
Bleu level adjustment.
Chapter 10 : RS-232 PROGRAMMER'S GUIDE (continued)
TYPE
MIN MAX
Rd
0
21
Please see value description (next section).
Rd/Wr
0
21
Please see value description (next section).
Rd/Wr
0
1
1 = start the transition (automatic reset at the
end of the effect duration).
0 = stop the transition (for holding effect).
Rd/Wr
0
1
0 = inactive
Rd/Wr
0
1
0 = inactive
Rd/Wr
0
1
1 = STORE action (automatic reset).
Rd/Wr
0
1
1 = STORE action (automatic reset).
Rd/Wr
0
1
1 = RECALL action (automatic reset).
Rd/Wr
0
1
1 = RECALL action (automatic reset).
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
21
Please see value description (next section).
Rd/Wr
0
1
0 = Input disable
0
1
0 = Hi-Z load
Rd/Wr
0
6
0 = SDTV YUV
1 = SDTV RGBS (TTL) 5 = comp (HV or C.)
2 = SDTV RGsB (SOG) 6 = HDTV.
3 = SDTV RGBS (ana)
Rd/Wr
0
4
0 = automatic standard detection.
1 = NTSC.
3 = SECAM
Rd/Wr
0
4
0 = 8 CV
1 = 6 CV + 1 SV
2 = 4 CV + 2 SV
Rd/Wr
0
10
0 = VGA 60 Hz
1 = SVGA 60 Hz
2 = XGA 60 Hz
3 = SXGA 60 Hz
4 = VGA 75 Hz
5 = SVGA 75 Hz
Rd/Wr
0
2
0 = Separate H &V sync. 2 =SOG
1 = Composite sync.
Rd/Wr
0
1
0 = Separate H &V sync. 1 = Composite sync.
Rd/Wr
0
1
0 = 4/3 screen
Rd/Wr
0
1
0 = OFF
Rd/Wr
0
1
0 = OFF
Rd/Wr
0
21
0 = Internal rate.
1 = RGB/YUV1 rate.
9 = COMPOSITE 9 rate.
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr
0
255
Rd/Wr = Read and write command.
VALUE
DESCRIPTION
1 = active.
1 = active.
1 = Input enable.
1 = 75Ω load.
4 = computer (SOG)
2 = PAL.
4 = Black & White.
3 = 2 CV + 3 SV
4 =
4 SV
6 = XGA 75 Hz
7 = D-ILA 4-3.
8 = D-ILA 16/9
9 = 480p
10 = 720p
1 = 16/9 screen
1 = ON
1 = ON
17 = S.VIDEO1 rate.
21 = SDI input rate.
PAGE 35
Publicité
Table des Matières
