Preset Programs; User Program; Additional Notes - Tunturi CROSS 3.0 Mode D'emploi

2. PRESET PROGRAMS

Preset program profile is shown for two seconds while
programs are browsed. Select desired preset program by
using the SELECTION DIAL.
Set time for training and/or target distance and/or energy
and/or upper heart rate limit by SELECTION DIAL.
Start training by pressing START/STOP button.
If you have set target/targets, the target/targets start to
count down. During training you can scale the load by
SELECTION DIAL.

3. USER PROGRAM

The program profile used last time is displayed. You can
either start training with your personal memorized training
targets by pressing START/STOP or modify the program.
The program profile bar (1/20) that can now be modified
blinks. If you want to change, modify the blinking bar and
confirm. Next bar will blink. After the last bar, the display
switches back to the first bar. By pressing the ENTER button
for 2 seconds you can finish the profile modifying. Now
program is ready with your memorized personal training
data (time, distance, energy targets and heart rate limit).
Modify your targets if needed. Start training by pressing
START/STOP button.
If you have set target/targets, the target/targets start to
count down. During training you can scale the load by
SELECTION DIAL
4. HEART RATEATE CONTROL (H.R.C.)
Select between four different training intensities (55%, 75%,
90% or TARGET). By selecting TARGET you can insert target
heart rate.
Start training by pressing START/STOP button.
During the training the equipment will automatically adjust
the resistance so that your target will be reached and
maintained.
5. CONSTANT WATT
Set target power in watts and target time and/or distance
and/or energy consumption and/or upper heart rate limit
by SELECTION DIAL.
Start training by pressing START/STOP button.
If you have set target/targets, the target/targets start to
count down. During training the equipment will adjust
resistance dependently on your pedaling speed, so that
target power level is achieved and maintained. You can
change the target power by SELECTION DIAL.
6. RECOVERY
Start the recovery calculation after training by pressing
RECOVERY button. Recovey heart rate calculation can
be started only if the heart rate measurement is activated
and the heart rate value is shown on the display The
measurement takes 60 seconds. After 60 seconds, the
display shows your recovery index F1-F6 (F1 = best result).
To get back to main menu, press RECOVERY button once
again.
7. BODY FAT
Press BODY FAT button to start measurement. Hold both
hands on the handgrips and wait for 8 seconds. The meter
will show body fat
Cross 3.0_RD_manual.indd 5
SETTING USER DATA
Right after restarting the meter or reset (long push) you
can enter to the user menu. Select the user and confirm.
Set your sex, age, height and weight. Confirm by selection
dial. Personal exercise target data (time, distance,
energy, heart rate limit) will be memorized and recalled
as defaults every time when the user is selected. If you
modify your personal training data, it will automatically be
memorized.

ADDITIONAL NOTES

1. For speed and distance you can choose either metric
or English units by using the KM/ML switch located on
the back cover of the meter. The power cord has to be
unplugged and replugged to apply the change.
2. If you are not training and buttons are not pressed,
the meter switches into the Sleep mode after about four
minutes. Room temperature is displayed.
3. Training is paused for a maximum of 4 minutes by
pressing the START/STOP button. Pressing the button again
allows you to continue the paused training session using
the previous training data.
4. Entering training targets (time, distance, energy, heart
rate limit) is possible only in the STOP mode (not during
training).
5. If you don't want to change your user data every
time you start training, press START/STOP to skip user data
editing. You'll enter to the training in Manual mode.
6. This equipment cannot be used for therapeutic
purposes.
7. Energy consumption is calculated based on average
values. The energy expenditure is displayed in kilocalories.
To convert this into joules, use the formula: 1 Kcal = 4.187
KJ.
8. If you are training with heart rate measurement (either
chest belt or handgrip heart rate) you can set maximum
heart rate limit. When limit is exceeded while training
meter will give alarm beeps.
9. Preset programs are divided into 16 steps. Duration
of the one step depends on the time set for the whole
training. If time is not set, duration of one step will be 100
m in distance.
10. If you have set targets to count down, a signal sounds
and training automatically stops when any of target
reaches zero. You can restart training by pressing START/
STOP
11. Note that recovery index is in relation to the heart
rate frequency in both the beginning and the end of the
measurement.
12. In H.R.C program heart rate target ranges (55%,
75% and 90%) are calculated as percent from your age
predicted maximum heart rate (calculation formula:
maximum heart rate = 220 – age).
13. Automatic adjustment of the resistance during
H.R.C program occurs upwards every 30 seconds and
downwards every 15 seconds, if needed.
5
Cross 3.0 - OWNER'S MANUAL
ENGLISH
9/24/2012 8:55:32 AM