Publicité
Determining the Top Line Location
of the Rear Wall Template under Your
Cabinet
Mounting Plate - Beneath flat bottom cabinet:
Draw a vertical line on the wall at the center of the 30"
(76.2cm) wide space. Tape the Rear Wall Template onto the
wall matching the centerline. The TOP LINE OF REAR WALL
TEMPLATE must align with cabinet bottom.
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
F. CUT OUT FOR HORIZONTAL
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
NOTE:
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
TOP LINE OF REAR WALL TEMPATE
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
16½" (41.9cm)
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
B
A
D
C
TOP LINE OF REAR WALL TEMPATE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
16½" (41.9cm)
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
B
Mounting Plate - Beneath framed recessed cabinet:
Draw a vertical line on the wall at the center of the 30" (76.2cm)
space. Tape the Rear Wall Template onto the wall matching the
centerline. The TOP LINE OF REAR WALL TEMPLATE must
align with the back frame of cabinet bottom.
Back frame of
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
F. CUT OUT FOR HORIZONTAL
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
that do not line up with a stud, drill 5/8" holes for
a stud, drill a 3/16" hole for wood screws. For holes
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
TOP LINE OF REAR WALL TEMPATE
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
B
A
D
C
TOP LINE OF REAR WALL TEMPATE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
4"
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
16½" (41.9cm)
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
B
D
Mounting Plate - Beneath framed recessed bottom
cabinet with front overhang:
Draw a line on the back wall equal to the depth of the front
overhang. The TOP LINE OF REAR WALL TEMPLATE must
be at the same distance below the cabinet bottom as the front
overhang.
CCD-0006072 Rev: 11-15-23
Front
Rear
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
F. CUT OUT FOR HORIZONTAL
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
versión en Español.
Darle vuelta a la hoja para consultar la
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
B
A
D
C
Min. 30" (76.2cm)
3/8" TO EDGE
12"
Trim the rear wall template along the dotted line.
F. CUT OUT FOR HORIZONTAL
4"
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
D
C
Front
Rear
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
F. CUT OUT FOR HORIZONTAL
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
NOTE:
right side of the centerline.
screw mounted firmly in a stud to support the weight
It is important to use at least one wood
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
NOTE:
toggle bolts.
AT THIS TIME.
DO NOT INSTALL THE MOUNTING PLATE
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
30" to cooktop
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
B
A
D
C
3/8" TO EDGE
12"
Trim the rear wall template along the dotted line.
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
C
Template must be at the same
Front overhang of
distance below the cabinet bottom as
cabinet bottom
the FRONT EDGE OVERHANG.
3/8" TO EDGE
NOTE: IT IS VERY IMPORTANT TO
12"
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
F. CUT OUT FOR HORIZONTAL
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
2. Locate and mark at least one stud on the left or
accurately.
right side of the centerline.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
NOTE:
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
TOP LINE OF REAR WALL TEMPATE
AREA.
B
D
C
TOP LINE OF REAR WALL TEMPATE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
16½" (41.9cm)
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
B
Your cabinets may have decorative trim that interferes with the
microwave installation. Remove the decorative trim to install
the microwave properly and to make it level.
Microwave Leveling
Use a level to make sure the cabinet bottom is level. If the
cabinets have a front overhang only, with no back or side
frame, top line of rear wall template must align with below
cabinet bottom, the same distance as the front overhang
depth. This will keep the microwave level.
1.
Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal distance
below the cabinet bottom as the inside depth of the front
overhang.
3. For this type of installation with front overhang only, align
top line of rear wall template with this horizontal line, not
touching the cabinet bottom as described in the "Aligning
the Top Line of the Rear Wall Template" section.
Aligning the Top Line of the Rear Wall
Template
Wear gloves to avoid cutting fingers on sharp edges.
1.
Draw a vertical line on the wall at the center of the 30"
(76.2cm) wide space.
2. Draw a horizontal line on the wall at the bottom of REAR
WALL TEMPLATE.
3. Find a wall stud in area "E" of mounting plate. Refer to the
"Finding the Wall Studs" section.
4. For attaching the mounting plate into stud drill a 3/16" hole
into wood stud. Drill a 5/8" hole for toggle bolt in one other
location (Hole A or Hole B).
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
NOTE: Holes A and B are inside area E. If neither of Holes A
and B are not in a stud, find a stud somewhere in area E and
draw a circle to line up with the stud. It is important to have at
least one wood screw mounted firmly in a stud to support the
weight of the microwave. Set the mounting plate aside.
- 5 -
Front
Rear
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
Trim the rear wall template along the dotted line.
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
F. CUT OUT FOR HORIZONTAL
REAR WALL TEMPLATE.
mounting plate and to locate the horizontal exhaust
This Rear Wall Template serves to position the bottom
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
2. Locate and mark at least one stud on the left or
accurately.
right side of the centerline.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
that do not line up with a stud, drill 5/8" holes for
a stud, drill a 3/16" hole for wood screws. For holes
toggle bolts.
NOTE:
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
5. Review the Installation Instruction book for your
4. Remove the template from the rear wall.
installation situation.
versión en Español.
Darle vuelta a la hoja para consultar la
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
A
DISCHARGE INTO HOUSE STRUCTURE.
30" to cooktop
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
REAR WALL TEMPLATE
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
Trim the rear wall template along the dotted line.
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
B
A
D
C
3/8" TO EDGE
12"
Trim the rear wall template along the dotted line.
F. CUT OUT FOR HORIZONTAL
4"
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
30" MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
D
C
CAUTION
Publicité
