Description Of Keys; Programming The Remote Control - THOMSON ROC 4206 Manuel D'utilisation

The ROC 4206 is a universal remote control (4 in 1). It can replace 4 remote
controls thanks to its 4 mode keys TV, DVD/VCR... It is compatible with the
majority of television sets, video cassette recorders, DVD players, satellite and
cable receivers as well as terrestrial digital television (DVBT), amplifiers and
other audio equipment provided they are controlled by infra red signals.
This remote control has been factory programmed to allow you to use it
immediately with the majority of Thomson Group devices.We therefore advise
you to try it before beginning to program it. If programming is necessary,
follow one of the methods A, B, C, D or E that are given in this manual. First
of all, please activate the remote control by removing the 2 protective tabs
from the 2 CR 2032 batteries.
Keep these instructions and the separate list of codes in a safe place so that
you can later reprogram your remote control.

1 - Description of keys

1 Remote control mode
Selects device to control:
TV = television set, flat screen, etc.
DVD/VCR = DVD player or recorder, video
recorder.
SAT = satellite or cable receiver
DVBT = DVBT receiver
2 Keys 0 to 9: select chapters or enter numbers
(channels, values, codes, etc.).
3 -/-- : Press this key first before you type in the
��digit channel number
4 Transport keys *** : B (play) � F (goes forward
or fast forward) � G (goes backward or fast
forward) � L ( = stop playback) � K (
STOP
= stops on an image) � M (
5 SETUP: programs the remote control.
6 Navigation keys: use menus and other interactive
displays (press the
SHIFT
with indications in blue (
same use as the original device.
7 TV functions (same functions as on your original
TV remote control):
For sound
= adjusts the volume
VOL+ / VOL-
c : sound off (
MUTE
For teletext
a (teletext On�Off) � I (return to TV programs)
� (stop page scrolling) �
picture) � J (information display)
8 B : switch on or off (
9 b : Select an external source (
sockets).
10 Operating indicator: lights up when a key is
activated and remains fixed or flashes during
programming.
*** The coloured buttons can be used to select categories
when teletext is activated, and specific functions depending
on the make.
2 - Testing the remote control
before programming
�. Turn on the device that you wish to control.
�. Press the key corresponding to the type of device
to control: TV, DVD/VCR...
PAUSE
= recording).
RECORD
key then one of the keys
, , , ...) =
MENU EXIT OK
function)
(teletext inlay on TV
)
POWER
, Audio�Video
AV
�. Point the remote control at the device you wish to
control and try to turn it off using the B key.
If the device does not turn off, you must program
the remote control using one of the methods A, B,
C or D as described below.
3 - Programming
the remote control
Method A – Fast programming with
1-digit subcode
Before you start programming, you must find the subcode of
the set to be controlled.
Refer to the list provided with these instructions, page I of
the codes.
� Switch on the set you want to control.
�. Hold down the SETUP key until the red indicator
lamp remains lit (the indicator light remains on for
a few seconds to give you the time to proceed with
the following steps.The indicator lamp flashes when
this time is almost up, and then goes off).
�. Press the key that corresponds to the type of
equipment you want to control: TV, DVD/VCR...
�. While the indicator is lit, type in the subcode
(example: � for Thomson).
�. Direct the remote control towards the set and try
to switch it off by pressing the B key.
�. If the set you want to control switches off, press c
to memorise the subcode.
If the product doesn't turn off, press the B
�.
key repeatedly until the set switches off. Wait
approximately one second between key presses to
give the red indicator lamp enough time to go off
and light up again.This will allow you to see whether
the product responds or not.
�. Immediately upon the switching�off of the set to be
controlled, press c to store the subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television set),
begin by entering the code that corresponds to the product
you want to programme (a 4-digit code that you will find in
the code booklet – see method B).
Example: if you want to control a satellite receiver with the
DVD/VCR key, begin by entering a satellite code (any
satellite, for example: 0603 for a Thomson satellite receiver)
then begin the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands. Check your remote control for proper functioning
by performing the test described on page 3.
1