Publicité
To interrupt the steam function, just press any key.
If the nozzle is blocked, clean it out with a fine needle.
The maximum duration for production of steam per cycle is limited to 2 minutes.
Setting up the Auto-cappuccino XS 6000 (sold separately)
This auto-cappuccino accessory makes it easier to make a cappuccino or a caffe latte.
Attach the various parts together. - Fig. 25.
Select the cappuccino or caffe latte position on the special nozzle - Fig. 26.
Fill up the milk pot - Fig. 27 and place a cup or a glass underneath the auto-cappuccino
nozzle - Fig. 28. Press the
button to start and then to stop the cycle.
Place your cup under the coffee outlets and start a coffee / espresso cycle - Fig. 29.
The tube must not be twisted to ensure that the button is held in the correct position.
To prevent milk from drying on the auto-cappuccino accessory, it must be cleaned
thoroughly after use.. It is recommend that you wash it immediately by carrying out a cycle
with steam and the accessory pot filled with water in order to clean the inside of the nozzle.
To do so, you can use liquid cleaner XS4000, available as an accessory.
MAINTAINING YOUR APPLIANCE
Caution! To benefit from the guarantee conditions, it is essential to perform the
appliance cleaning or a scale removal cycle when informed to do so. Be sure to follow
the order of operations. You can continue to use the appliance, but you are advised to
perform the program as soon as possible.
Emptying the used coffee collector and the drip collector tray
If the above message appears- Fig. 30, remove, empty and clean the drip tray (the drip tray
may contain coffee grains).
Remove, empty and clean the coffee grounds collector - Fig. 31.
Replace the coffee grounds collector - Fig. 32.
The drip tray is equipped with floats to tell you when to empty it.- Fig. 33.
As soon as you remove the coffee grounds collector, you will have to empty it completely
to avoid any overflow.
The warning message will remain displayed if the coffee grounds collector is not slotted
in fully or not fitted correctly. You cannot make espresso or coffee while the warning
message is displayed.
The coffee grounds collector has a capacity of 9 coffees.
Rinsing out the circuits: see page 17
Machine cleaning program – total duration: about 13 minutes
You should perform the cleaning program about every 350 preparations of espresso or
coffee.
The appliance will let you know when you need to proceed with cleaning through the 'clean'
light coming on.
20
To perform the cleaning program, you will need a container with minimum capacity of 0.6
litres and a KRUPS (XS 3000) cleaning tablet.
If your machine is unplugged when cleaning or if there is a power cut, the cleaning
programme will re-start at the step in progress when the incident occurred. You will
not be able to postpone this operation. This is essential due to water system rinsing
reasons. In this case, a new cleaning tablet may be required. Be sure to complete
the entire cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning
solutions are accidently swallowed). The cleaning cycle is a continuous cycle and the
pump can be heard intermittently. Do not put your hands under the coffee outlets
during the cycle.
Press the
key to start the automatic cleaning program when the "Cleaning needed"
message is displayed. Just follow the instructions shown on the screen.
The automatic cleaning program is in 2 parts – the cleaning cycle itself, then 1 rinsing cycle.
This program lasts about 13 minutes. Press
choose MAINTENANCE => OK => CLEANING from the menus displayed.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage
that may result from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Automatic scale removal program – total duration: about 20 minutes
If your product is equipped with our Claris - Aqua Filter System cartridge F088 - Please
remove this cartridge during the descaling operation.
The quantity of scale deposited depends on the hardness of the water used. The appliance
will automatically warn you with a message when you need to proceed with scale removal.
To perform the cleaning program, you will need a container with minimum capacity of 0.6
litres and a KRUPS F 054 (40 g) cleaning sachet.
Press the
key to start the automatic cleaning program when the "Scale removal
needed" message is displayed. Just follow the instructions shown on the screen, making
sure the sachet dissolves fully.
The scale removal program is in three parts – the scale removal cycle itself, then 2 rinsing
cycles.
Only use KRUPS scale removal products. You can obtain scale removal products from
KRUPS Service Centres. The manufacturer may not be held responsible for damage to the
appliance through use of other products.
If a power cut occurs during the cycle or if you unplug your machine, the cycle will
re-start at the step in progress when the incident occurred, without the option of
postponing this operation.
Be sure to complete the entire scale removal cycle to avoid any risk of intoxication. The
scale removal cycle is a continuous cycle and the pump can be heard intermittently. Do not
put your hands under the coffee outlets during the cycle.
Make certain to protect your work surface during scale removal cycles, especially if
they are made of marble, stone or wood.
General maintenance
Always remove the power supply cord from the socket and let your appliance cool down
to perform cleaning at any time and then
21
Publicité
