Publicité
BEFORE FIRST USE
Measuring water hardness
Before using the appliance for the first time or if you have noted a change in water hardness,
it is advisable to adapt the appliance to the observed water hardness. To determine the
water hardness, use the measuring stick included with the appliance or contact your water
supplier. The appliance will ask you for the hardness of your water on first use.
Degree of
0
1
hardness
very soft
soft
° dH
< 3°
> 4°
° e
< 3.75°
> 5°
° f
< 5.4°
> 7.2°
Setting
0
1
machine
water testing: Fill a glass with water and immerse a water testing stick into it.
After 1 minute the hardness measurement will appear (moderately hard water) - Fig. 1 and 2.
Claris - aqua filter system F 088 cartridge (sold separately)
To get the best taste from your coffee and extend your appliance's service life, we advise
you to use only the Claris - Aqua Filter System cartridge sold as an accessory.
Fig. 3 : Mechanism to memorise the month the cartridge was fitted and when to replace it
(after 2 months at most).
Your appliance will give you a message telling you when to replace your Claris - Aqua
Filter System cartridge.
Putting the filter in place
To prime the cartridge correctly, follow this procedure every time you fit a cartridge.
Using for the first time : Choose the "YES" option in the "FILTER" function and follow the
instructions on the screen.
When using later or replacing the cartridge : Select the "FILTER" function using the
button : Maintenance -OK - Filter - OK - Place or change -OK - and follow the
instructions on the screen. Screw the filtering cartridge into the bottom of the water tank
using the spanner provided - Fig. 4.
Place a 0.6 L container underneath the steam nozzle. - Fig. 5.
Preparing the appliance
Pull out and fill the water tank - Fig. 6.
Put it back in place by pressing firmly and close the lid again - Fig. 7. Open the coffee bean
container lid. Add the coffee beans - Fig. 8.
Close the coffee bean container lid again - Fig. 9.
16
4
2
3
extremely
moderately hard
hard
hard
> 7°
> 14°
> 21°
> 8.75°
> 17.5°
> 26.25°
> 12.6°
> 25.2°
> 37.8°
2
3
4
Do not fill the water tank with hot water, milk or any other liquid. If you turn on the
appliance when the water tank is not in place or not correctly filled (under the "min."
level,), the "fill water tank" light will come on and making an espresso or a cup of coffee
will be made impossible.
First use / setting up the appliance
Use the rotating button to select a function, increase or reduce values. Confirm your choice
using the OK key.
Press "On / Off" to turn your appliance on. Follow the instructions that appear on the "choice
of language" screen - Fig. 10. Use the rotating button - Fig. 11, to choose a language
(highlighted) - Fig. 12.
Press the OK key to validate - Fig. 13.
When you first use your appliance, it will ask you to set several parameters. If you unplug
your appliance, you will again be asked for some of these parameters.
The appliance will ask you to set:
Language
You can select your chosen language from those offered.
Measurement unit
Choose either ml or oz as your measurement unit.
Date
You must set the date.
Clock
You can choose between 12 hour or 24 hour time display.
Auto-off
You can choose the period after which your appliance will stop
automatically.
Auto-on
You can automatically start pre-heating of your appliance at your
chosen time.
Water hardness
You must set your water hardness between 0 and 4. See "Water
hardness measurement" section.
Filter
You must indicate whether a filter is fitted or not (Claris – Aqua
Filter System cartridge)
When being used for the first time, it is possible that the machine will ask to be filled up. Just
follow the instructions on the screen.
Rinsing of circuits
Rinsing out the coffee circuit :
Once you have turned the machine on and the preheating stage has completed, you can
rinse out the coffee circuit. Place a container under the coffee outlets then select "YES"
from the menu proposed.
Rinsing out the steam circuit :
Place a container under the steam nozzle. Press the
Fig. 14. The rinsing cycle will stop automatically after the volume of water displayed has
flowed through.
Press
at any time to display menus to perform rinsing and then select MAINTENANCE
=> OK => RINSING.
It is best to perform rinsing after the appliance has remained unused for several days.
WHEN RINSING PROCESS IS IN PROGRESS, HOT WATER COMES OUT THROUGH
THE NOZZLES. BE CAREFUL NOT TO BE SCALDED.
key to rinse the steam circuit -
17
Publicité
