Publicité
EN
Using your Dyson machine
Please read the 'Important safety instructions' in your Dyson User
manual before proceeding.
Carrying the appliance
•
Carry the appliance by the main handle.
•
Do not press the cyclone release button or shake the appliance when
carrying or the cyclone could disengage, fall off and cause injury.
Operation
•
Always extend the cable fully to the red tape before use.
•
Plug the appliance into the mains electricity supply.
•
To switch 'ON' or 'OFF' press the red power button, located
as shown.
•
After use: Unplug, push the cable retract button firmly until cable has
fully retracted.
•
Switch 'OFF' the appliance and unplug before:
– Changing tools.
– Removing the hose.
Self-adjusting cleaner head with
suction control
•
Your appliance has a self-adjusting cleaner head with suction control.
This cleaner head is used for testing with the European Regulations:
No. 665/2013 and No. 666/2013 and testing shall be performed in
Max mode (+).
Easy mode (-)
Reduced push force for effortless cleaning.
•
For vacuuming of lightly soiled carpets, rugs and hard flooring.
•
Your appliance is pre-set to this level of suction when you take it out of
the box.
Max mode (+)
Maximum suction for powerful dust and dirt removal.
•
For vacuuming durable floor coverings, hard floors and heavily soiled
carpets and rugs.
•
To switch to this setting, move the suction control slider on top of the
cleaner head as shown.
•
CAUTION: The suction of this mode can damage delicate
flooring. Before vacuuming, check the flooring manufacturer's
cleaning recommendations.
•
If the suction power of Max mode (+) prevents easy manoeuverability,
switch to Easy mode (-).
Carpets or hard floors
•
The brush bar will always default to 'ON' (spinning) each time you
switch the machine 'ON'.
•
To switch the brush bar 'OFF' (e.g. for delicate flooring), twist the dial
on the cleaner head a quarter of a turn. The brush bar will stop.
•
When the appliance is running and the brush bar has been switched
'OFF', the brush bar can be switched 'ON' again by twisting the
dial on the cleaner head a quarter of a turn. The brush bar will start.
Alternatively, switch the appliance 'OFF'; the dial will return to its
original position. When the appliance is switched 'ON' again the
brush bar starts automatically.
•
The brush bar can only be turned off once the machine is running.
•
The brush bar will automatically stop if it becomes
obstructed. See 'Brush bar – clearing obstructions'.
•
Before vacuuming your flooring, rugs and carpets, check the
manufacturer's recommended cleaning instructions.
•
Some carpets may fuzz if a rotating brush bar is used when
vacuuming. If this happens, we recommend vacuuming with the brush
bar switched 'OFF' and consulting with the carpet manufacturer.
•
The brush bar on the appliance may damage some carpet types.
If you are unsure, turn 'OFF' the brush bar.
•
Your machine has carbon fibre brushes. Take care if coming into
contact with them, as they may cause minor skin irritation. Wash your
hands after handling the brushes.
•
Check the brush bar regularly and clear away any debris (such as
hair). Debris left on the brush bar may cause damage to flooring
when vacuuming.
Using your machine
•
Do not use without the clear bin and cyclone in place.
•
Do not use on rubble, ash or plaster. This appliance is designed only
for domestic use to remove household dirt, hair and allergens. The
appliance is not designed to be used on:
– debris produced from activities such as DIY, building or
similar tasks
– larger types and quantities of dust or debris, such as soot
and sawdust.
These materials may harm the appliance and may void
your guarantee.
•
Fine dirt such as flour should only be vacuumed in very
small amounts.
•
Do not use the appliance to pick up sharp hard objects, small toys,
pins, paper clips, etc. They may damage the appliance.
•
When vacuuming, certain carpets may generate small static charges
in the clear bin or wand. These are harmless and are not associated
with the mains electricity supply. To minimize any effect from this
small static charge, do not put your hand or insert any object into the
clear bin unless you have emptied it first, then cleaned it with a damp
cloth (see 'Cleaning the clear bin').
•
Do not work with the appliance above you on the stairs.
•
Do not put the appliance on chairs, tables, etc.
•
Before vacuuming highly polished floors, such as wood or lino, first
check that the underside of the floor tool and its brushes are free from
foreign objects that could cause marking.
•
Do not push hard with the floor tool when vacuuming, as this may
cause damage.
Blockages – thermal cut-out
•
This appliance is fitted with an automatically resetting thermal cut-out.
•
If any part becomes blocked the appliance may overheat and
automatically cut-out.
•
If this happens, follow the instructions in 'Looking for blockages'.
•
NOTE: Large items may block the tools or wand inlet. If this happens,
do not operate the wand release catch. Switch 'OFF' and unplug.
Failure to do so could result in personal injury.
1
2
3
31
Publicité
