Publicité
can be displayed in units of [bar], [PSI] or
[kPa]n.
•
The button (14) allows the desired pressure
to be reduced.
•
The button (16) allows the desired pressure
to be increased.
•
To switch on the tool, press the pushbutton
for compressed air mode (18).
•
The inflator will then pump until the preset
pressure on the display is reached, then it will
switch off.
•
Warning! Observe the information supplied
by the tire manufacturer and the vehicle
manufacturer relating to the recommended
tire pressure.
•
Warning! This equipment is not calibrated!
For a calibrated measurement value, check
the actual tire pressure using a calibrated
meter after you have inflated the tires
yourself, e.g. at a gas station.
•
Just before it is switched off, the pressure
which is shown in the display can be
0.73 - 2.9 PSI (0,05 - 0,2 bar) higher than
the preselected pressure, because of
overpressure in the air hose.
•
Allow the inflator to cool down for about 5
minutes after every 5 minutes of operation in
order to prevent overheating.
6.2 Low-pressure blower operation
(Fig. 1a, 3, 4)
6.2.1 Suctioning air (Fig. 1a, 3)
•
To deflate objects with a large volume until
they are empty (e.g. deflating an air mattress,
etc.), connect the air hose (3) to the extractor
connection (13).
•
Connect the air hose to the object you wish
to deflate.
•
Switch on the tool by pressing the pushbutton
for low-pressure mode (12).
•
Switch off the equipment once the object has
been sufficiently deflated.
6.2.2 Infl ating (Fig. 1a, 4)
Warning! When using the equipment to infl ate
objects, check the information and safety
instructions provided by the manufacturer.
•
To inflate objects with a large volume (e.g.
inflating an air mattress, etc.), connect the air
hose (3) to the inflating connection (4).
•
Connect the air hose to the object you wish to
inflate. Use the adapter (10) if necessary.
•
Switch on the tool by pressing the pushbutton
for low-pressure mode (12).
Anl_PRESSITO_18_25_NA_SPK7.indb 13
Anl_PRESSITO_18_25_NA_SPK7.indb 13
EN
•
Switch off the equipment once the object has
been sufficiently inflated.
6.3 Sleep mode (Fig. 2)
The equipment will switch to sleep mode if it is not
used for 5 minutes. To reactivate the equipment,
press the "Bar/PSI/kPa / wake-up" button (15).
6.4 Charging the Lithium-Ion battery
(not included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.5 Battery capacity indicator
(Fig. 2 / item 20)
Press the battery capacity indicator switch (19).
The battery capacity indicator (20) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
7. Cleaning and maintenance
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
- 13 -
27.06.2024 11:15:24
27.06.2024 11:15:24
Publicité
