Publicité
OPERATION
Lubrication
NOTICE:
When filling the chain oil for the first
time, or refilling the tank after it has been com-
pletely emptied, add oil up to the bottom edge of
the filler neck. The oil delivery may otherwise be
impaired.
NOTICE:
Use the saw chain oil exclusively for
Makita chain saws or equivalent oil available in
the market.
NOTICE:
Never use oil including dust and parti-
cles or volatile oil.
NOTICE:
When pruning trees, use botanical oil.
Mineral oil may harm trees.
NOTICE:
Before the cutting operation, make sure
that the oil tank cap is tightened securely.
Saw chain is automatically lubricated when the tool is in
operation. Check the amount of remaining oil in the oil
tank periodically.
► Fig.13: 1. Oil tank
To refill the tank, place the tool on a flat surface, then
push the button on the oil tank cap so that the button on
the other side stands up, and then remove the oil tank
cap by turning it.
The proper amount of oil is 160 ml. After refilling the
tank, make sure that the oil tank cap is tightened
securely.
► Fig.14: 1. Oil tank cap 2. Tighten 3. Loosen
NOTE: If it is difficult to remove the oil tank cap,
insert the box wrench into the slot of the oil tank
cap, and then remove the oil tank cap by turning it
counterclockwise.
► Fig.15: 1. Slot 2. Box wrench
After refilling, hold the tool away from the tree. Start it
and wait until lubrication on saw chain is adequate.
► Fig.16
Working with the tool
CAUTION:
Keep all parts of the body away
from the saw chain when the motor is operating.
CAUTION:
Hold the tool firmly with both
hands when the motor is running.
CAUTION:
Do not overreach. Keep proper
footing and balance at all times.
CAUTION:
When cutting through branches,
be careful not to lose your balance due to the
weight of the tool head.
CAUTION:
Always keep escape route in case
a cut branch falls towards the operator.
CAUTION:
Never use the tip of the guide bar
for cutting. Otherwise, dangerous kickback may
occur, and it may result in personal injury.
NOTICE:
Never toss or drop the tool.
NOTICE:
Do not cover the vents of the tool.
NOTICE:
Do not force the tool. Otherwise, it may
damage the tool.
Stand on a stable surface, and hold the tool away from
the branches so that the angle of the tool becomes 60°
or less against the horizontal ground.
► Fig.17: 1. 60° or less
Start the tool, and then press the saw chain onto the
branch lightly.
When cutting long branches, in order to control the drop
position of cut branches, divide the branch in sections
and cut the branch from the tip. Pay attention to the
falling branches since they may bounce in the direction
of the operator after hitting the ground.
► Fig.18
When cutting thick branches, first make a shallow
undercut and then make the finish cut from the top.
► Fig.19
If you try to cut off thick branches from the bottom, the
branch may close in and pinch the saw chain in the cut.
If you try to cut off thick branches from the top without a
shallow undercut, the branch may splinter.
► Fig.20
Carrying tool
Before carrying the tool, always remove the battery
cartridge or the spark plug cap, and then attach the
guide bar cover. Also cover the battery cartridge with
the battery cover.
► Fig.21: 1. Guide bar cover 2. Battery cover
MAINTENANCE
CAUTION:
Always be sure that the motor is
switched off and the battery cartridge or the spark
plug cap is removed before attempting to perform
inspection or maintenance.
CAUTION:
Always wear gloves when perform-
ing any inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Sharpening the saw chain
Sharpen the saw chain when:
•
Mealy sawdust is produced when damp wood is
cut;
•
The chain penetrates the wood with difficulty, even
when heavy pressure is applied;
•
The cutting edge is obviously damaged;
13 ENGLISH
Publicité
