Publicité
Page 6 of 14
FITTING INSTRUCTIONS
•
Remove the rear pillion seat or seat cowl.
Remove any rubber straps or cable ties holding the indicator and licence plate light connectors in
•
place.
•
Inside the tail unit, locate the connections for the OEM indicators and licence plate light as shown
in Pictures 1 & 2 and disconnect.
While supporting the OEM licence plate hanger, remove the two bolts holding the tail unit to the
•
inside of the tail unit as shown in picture 3.
Remove the last bolt from the underside of the tail unit and carefully remove the OEM licence plate
•
unit threading the loose connectors through the opening of the tail unit.
Disassemble the OEM licence plate unit by removing the back screws holding 2 pieces together.
•
Disconnect the licence plate light connector and remove the loom from the unit for re-use as shown
•
in picture 4.
If re-using, remove the OEM indicators from the unit, noting which side connects to the
•
corresponding connector on the sub-loom.
R&G Tail Tidy Assembly
Cover the licence plate light (LA0002 – item 3) wires in heat shrink (item 12) and heat to seal
•
the wires together before using the M4 nuts and washers provided with the licence plate illuminator
assembly to fix to the tail bracket (Item 1) as shown in Assembly Drawing 1 on page 2 and use the 6mm
socket to secure the nuts.
Assemble the R&G tail tidy as shown in the Assembly Diagram on pages 1 & 2, ensuring to pass
•
the indicator wires & replacement licence plate light through the cover plate and through the hole on part
1 as shown in picture 5.
If not already fitted, affix the LA0002 light shroud to the light assembly using a small amount of
•
adhesive, this shroud will help direct the light towards the licence plate once fitted.
Ensure to fit the rubber bungs (item 11) into the holes shown with the larger side facing up (these
•
will sit against the bike tail unit)
The OEM indicator assembly will fit to the R&G tail tidy in the same way as they were removed.
•
Attach the indicators by threading the wires through the tail bracket (TB0381 - Item 1). And fix using
the m6x 20mm bolts (item 6) M6 washers (item 8) and 2 x nyloc nuts (item 10).
Affix the cover plate (item 2) using the M5 button head bolts (item 4). Ensure the indicator wires
•
pass through the gaps left in the side of the cover plate. The wiring should resemble the bracket shown in
picture 6.
With the tail tidy now assembled, it can be affixed to the bike as shown in picture 7. Offer up to
•
the bike and ensure the locating spacer sit into the metal subframe of the bike. During this step, ensure
the wires do not become trapped or crushed between the tail bracket and mounting bracket surfaces.
•
Push the wires through the opening in the tail unit and pass the indicator connectors and fix in
place using 2 x M6x30mm bolts (item 7) with larger M6x20mm washers (item 9) per bolt. Pass the bolts
through the tail tidy and tail unit and secure these bolts with an M6x12mm washer (item 8) and an M6
Nyloc nut (item 10).
Fix the remaining mount hole on the underside of the bike using an M6x15mm bolt (item 5) and
•
M6x12mm Washer (item 8).
•
Connect the wires from the replacement licence plate light to the CON014 connector provided
(item 14) ensuring black to black wires correspond.
Connect the new connector to the sub-loom as shown in picture 8. Connect this to the main wiring
•
loom.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
www.rg-racing.com
R&G
Email:
info@rg-racing.com
LP0381
Publicité
