Publicité
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the
trouble may lie in another component. Inspect the other
components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks
listed below, ask your nearest MARANTZ service center or
your dealer to carry out repair work.
The disc table comes back out automatically, shortly after
the disc table is closed.
The disc is dirty or warped.
\ Refer to 'Disc Care' (page 48).
The disc is not placed properly on the disc table.
\ Use the disc table guide to align the disc (page 18).
Region number does not conform with this unit.
\ If the region number on the disc does not match the
number on the player, the disc cannot be used (page
54).
There is condensation on the operating section of the
player.
\ Allow time for condensation to evaporate. If player is
near an air conditioning unit, you should move the
player (page 49).
Playback is not possible.
The disc has been loaded upside down.
\ Check that the disc has been loaded with the label
side facing up.
mark appears on screen.
The selected function does not operate for that disc.
mark appears on screen.
The operation is prohibited by the player.
Picture playback stops and the operation buttons cannot
be used.
Player malfunctions.
\ Stop disc playback (press STOP 7), then start
playback again.
New settings made in the Setup screen menus while a
disc is playing are ineffective.
Some settings can be changed while a disc is playing, but
are not effective. This is not a malfunction.
\ Make the same setting when the player is stopped.
\ Stop disc playback (press STOP 7), then start
playback again. When playback is resumed, the new
settings should be in effect. Please note that making
settings in the Setup screen menus may cancel the
resume function.
When making changes in the Setup screen menus,
displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\ The setting will be effective the next time a DVD is
loaded.
No picture.
The rear panel's VIDEO OUT SELECT switch setting is not
correct.
\ Check that the VIDEO OUT SELECT switch is set to
the correct position for the monitor connection you are
using (page 14).
Connection is incorrect.
\ Check that cord connections are correct and that plugs
are firmly connected.
Operation (settings) of TV or AV amplifier is not
appropriate.
\ Be sure that your TV, receiver, or amplifier is set up to
view DVD playback.
The [Component Video] menu is set to [progressive] but
your TV/monitor is not compatible with progressive scan.
\ Reconnect the player to your TV using a composite or
S-video cord, then set set the VIDEO OUT SELECT
switch on the rear panel to COMPOSITE & S-VIDEO.
With your TV connected using either the composite or
S-Video terminals, choose the [Interlace] setting in the
[Component Video] menu, then set the rear panel
switch back to COMPONENT (page 27).
\ Reset the player (page 47). [Component Video] will
be reset to [Interlace] but you'll also loose other
settings.
\ Check that the VIDEO OFF switch is set to the correct
position (page 47).
The screen is stretched or aspect does not change.
The multi aspect setting is not appropriate.
\ Change the aspect setting in the [TV Screen] setting in
the Setup screen Video menu to the screen type most
appropriate to the TV or monitor you are using (page
26).
This is not a malfunction.
\ The aspect ratio of some progressive-scan compatible
TVs cannot be changed.
Picture disturbance during playback or dark.
This is not a malfunction.
\ This player is compatible with Macro-Vision System
copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
stripes etc., may appear on some sections of the
picture depending on the TV.
When using progressive-scan.
\ If your TV is connected using the COMPONENT
VIDEO OUT jacks, set the [Component Video] menu
to [Interlace] (page 27).
When recorded on a VCR or passed through an AV
selector, there is disturbance in the playback picture.
This is not a malfunction.
\ Due to the player's copy protection circuits, connection
of this device through a VCR or an AV selector may
prevent recording or cause picture problems.
is
Remote control operation is not possible.
The rear panel control input jack on the player is being
used.
\ Point the remote control at the component that the
player is connected to (page 14).
The remote control is too far from the player, or the angle
with the remote sensor is too wide.
\ Be sure to operate the remote from a location within its
operating range (page 8).
The batteries are exhausted.
\ Replace the exhausted batteries with all new batteries
(page 8).
ENGLISH
53
Publicité
