Publicité
ENGLISH
Adjusting
Audio and
Video Settings
Using the Setup Screen
Menus
The procedure on this page describes how to operate the
menus on the Setup screen. These menus are used to set and
adjust a number of system settings. The various functions that
can be adjusted are covered throughout this manual. The
procedure on this page provides a basic outline for using the
Setup screen menus.
When setting up for the first time
It is recommended to set up player using the Setup Navigator
(page 15). If you selected [Auto Start Off] when the Setup
Navigator appeared, you may still set up the player using the
Setup Navigator in the General menu screen.
If you choose not to use the Setup Navigator, be sure to make
the necessary settings in the Setup screen
Audio 1, Audio 2, Video, and Language menus as
described on the following pages.
Some DVDs start playing automatically when loaded in the
player. If a DVD has been loaded, be sure to press STOP 7
before proceeding.
OPEN/CLOSE
VIDEO ON/OFF
1
4
7
T-C
TOP
MENU
3, 4, 5, 6
RETURN
ANGLE
PROGRAM
SETUP
2
1
DVD PLAYER DV7110
OPEN/CLOSE
V I D E O
STANDBY
POWER
ON/OFF
1
DIGITAL OUT
22
A-B
REPEAT
RANDOM
2
3
5
6
8
9
+10
CLEAR
0
MENU
ENTER
SUBTITLE
AUDIO
LAST
OSD
MEMORY
CONDITION
DIMMER
MEMORY
REMOTE CONTROLLER
RC7010DV
STOP
PLAY
REPEAT
A-B
REPEAT
SHUFFLE
SVCD
SCAN
CHAPTER
TITLE
TRACK
TITLE
DTS
CHAPTER
TRACK
PBC
FTS
TOTAL
TRACK
TIME
FL OFF
PAUSE
LEVEL
PHONES
DIMMER
VIDEO OFF
OSD
-
+
1
Press Power on the front panel.
2
Press SETUP.
The Setup screen appears.
(Example)
Audio1
Audio2
Video
Language
Dolby Digital Out – Dolby Digital
DTS Out – Off
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Setup audio
Digital output format/tone adjust
Move
3
Use the cursor buttons (2 2 2 2 2 /3 3 3 3 3 ) to select the
menu you want.
As each menu is selected with the cursor, the settings
appear below the menu heading.
4
Use the cursor buttons ( ) to enter the menu.
The top item within the menu becomes highlighted.
(Example)
Audio1
Audio2
Video
Language
Dolby Digital Out
DTS Out -
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Change Dolby Digital output mode
Move
5
Use the cursor buttons (5 5 5 5 5 / ) to select the
setting you want to change.
The options available for each setting appear to the right
when the setting is selected. The current setting appears
with the setting indicator lit.
6
Use the cursor buttons (3 3 3 3 3 ) to enter the setting
options.
(Example)
Audio1
Audio2
Video
Language
Dolby Digital Out
DTS Out -
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Output Dolby Digital
Move
ENTER
• Not all menu options can be changed while a disc is
playing. In these cases, the options appear grayed out
on the screen and cannot be adjusted. To change
these settings, press STOP 7 first before pressing
SETUP.
• Operating the menu after pressing STOP 7 may
cancel the resume function.
• Some menu options are not immediately effective if set
while a disc is playing. To make these settings
effective, stop playback and then start again, or
change the settings while the disc is stopped.
General
Exit
SETUP
General
Dolby Digital
Dolby Digital 3 PCM
Exit
SETUP
General
Dolby Digital
Dolby Digital 3 PCM
Select
SETUP
Exit
continued
Publicité
