Publicité
5
Plug in, switch on and select a speed. (Refer
to the recommended usage chart).
The processor will not operate if the bowl,
lid or wide feed tube are not fitted correctly
into the interlock. Check that the feed tube
is positioned to the front and the handle is
situated to the right hand front corner.
Use the pulse (P) for short bursts. The pulse
will operate for as long as the control is held
in position.
6
Reverse the above procedure to remove the
lid, attachments and bowl.
Always switch off and unplug before
removing the lid.
Important
Your processor is not suitable for crushing
or grinding coffee beans, or converting
granulated sugar to caster sugar.
When adding almond essence or flavouring
to mixtures avoid contact with the plastic as
this may result in permanent marking.
Weighing Function /Count up
Timer
Illustration
Your food processor is fitted with a built in
weighing function to allow ingredients to be
weighed straight into the bowl or blender goblet.
The Maximum weighing capacity is 3kg.
To Use The Weighing Function
1
Always fit the bowl, detachable drive shaft
and attachment or blender goblet onto the
power unit before adding ingredients.
2
Plug in – the display screen will show '-----'.
3
Press the ON/ZERO button once. The display
screen will light up, flash '0g', followed by a
steady '0g'.
4
Press the (kg/lb) button to select either
grams or ounces. The display will default to
kg/g when first switched on.
The unit weighs in 1g increments and
teaspoon/tablespoon measures are
recommended for weighing small quantities.
To zero press the ON/ZERO button once.
5
Weigh the required ingredients straight into
the bowl or goblet.
6
After all the ingredients are weighed fit the lid
and select a speed to operate the processor.
The weight of any additional ingredients
added down the feed tube whilst the
processor is running will not be shown on the
display screen.
The display screen can be turned off manually
by pressing and holding down the ON/ZERO
button for a few seconds.
Refer to the troubleshooting guide if you
experience any problems with operating the
weighing function.
Weighing Tray
A removable weighing tray is supplied for
weighing ingredients without the bowl or
blender.
To use, place the tray on top of the power unit
and turn clockwise to secure. Then follow steps 2
to 4 under 'To Use The Weighing Function'.
To remove, rotate the tray anti-clockwise and lift
off.
Count up timer
During operation the display screen will
automatically operate as a count up timer.
The timer will count up in seconds and will
pause whenever the speed control is turned
to 'ON' position.
To reset the timer to zero press the ZERO
button.
Using The Attachments
Refer to the usage chart, illustrations
and relevant section for each
attachment.
Glass Blender
16A
To Use Your Blender
Illustrations
16A
1
Fit the sealing ring into the blade unit -
ensuring the seal is located correctly in the
grooved area.
Leaking will occur if the seal is damaged or
incorrectly fitted.
2
Screw the goblet onto the blade assembly.
Refer to the graphics on the underside of the
blade unit as follows:
- Unlocked position
- Locked position
3
Put your ingredients into the goblet.
4
Fit the lid to the goblet and push down to
secure. Fit the filler cap.
5
Place the blender onto the power unit and
turn clockwise to lock.
The appliance will not operate if the blender
is incorrectly fitted to the interlock.
Plastic Blender
16B
Illustrations
16B
1
To assemble and use - refer to the Blender
illustrations and the Recommended Usage
Chart.
2
Put your ingredients into the goblet.
3
Fit the lid onto the goblet and turn clockwise
until it clicks.
4
Fit the blender to the power unit and turn
clockwise to lock in position.
3
(if supplied)
(if supplied)
Publicité
