Scheppach BC-RHD230-X Mode D'emploi page 19

Noise data
Sound pressure L
pA
Sound pressure L
wA
Measurement uncertainty K
Vibration parameters
Vibration a
h
Measurement uncertainty K
The total vibration emission values specified and the de-
vice emissions values specified have been measured in
accordance with a standardised test procedure and can
be used for comparison of one electric tool with another.
The total noise emission values specified and the total vi-
bration emission values specified can also be used for an
initial estimation of the load.
WARNING
The noise emission values and vibration emis-
sion value can vary from the specified values
during the actual use of the power tool, de-
pending on the type and the manner in which
the electric tool is used, and in particular the
type of workpiece being processed.
Try to keep the stress as low as possible. For example:
Limit working time. In doing so, all parts of the operating
cycle must be taken into account (such as times in
which the power tool is switched off or times in which it
is switched on, but is not running under a load).
7 Unpacking
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the trans-
port company that delivered the Product. Later claims
will not be recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
92.6 dB
100.6 dB
3 dB
pA
10.287 m/s
1.5 m/s
www.scheppach.com
8 Before commissioning
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
2 change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
2
unintentionally.
8.1 Inserting/removing the battery (11)
in the battery mount (10) (Fig. 2)
Note:
If necessary, swivel the additional handle (13) before in-
serting the battery (11). 9.6
Inserting the battery
1. Put the rotational direction switch (7) in the middle po-
sition (lock).
2. Push the battery (11) into the battery mount (10). The
battery (11) clicks into place audibly.
Removing the battery
1. Press the unlock button (12) of the battery (11) and
remove it from the battery mount (10).
8.2 Inserting the tool attachment
(15/ 16/ 17/ 18/ 19) (Fig. 1, 3)
CAUTION
Keep your hands away from the tool attachment when
the product is in operation.
Note:
Clean the shaft of the tool attachment and grease it lightly.
Note:
The dust cap (2) largely prevents drilling dust from entering
the tool receiver during operation. When inserting the tool
attachment*, take care not to damage the dust cap (2).
ATTENTION
A damaged dust cap must be replaced immediately. It
is recommended to have this done by a service centre.
1. Pull the locking sleeve (3) backwards to unlock the
SDS-Plus tool receiver (1).
2. Insert the tool attachment (15/ 16/ 17/ 18/ 19) into the
SDS-Plus tool receiver (1) by turning it.
3. Release the locking sleeve (3).
4. Check that the tool attachment (15/ 16/ 17/ 18/ 19) is
firmly seated by pulling on it.
The tool attachment (15/ 16/ 17/ 18/ 19) has some ra-
dial play due to the system.
GB | 19