Bosch GWS 27-230 J Professional Notice Originale page 20

20 | English
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Store the application tools inside buildings, in a dry,
u
frost-free room at a uniform temperature.
Remove the application tools before transporting the
u
power tool. This will allow you to avoid damage.
Bonded cutting and grinding discs have an expiration
u
date, after which the discs must no longer be used.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting and brushing metal
and stone, roughing metal,plastics and composite materials,
as well as making holes in stone materials using diamond an-
nular cutters, without the use of water. Make sure that the
correct protective guard is used (see "Operation",
page 23).
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Technical Data
Angle Grinder
Article number
Rated power input
A)
Rated no-load speed
Max. grinding disc diameter/rubber sanding pad diameter
Grinding spindle thread
Max. thread length of grinding spindle
Soft start
1 609 92A 9L8 | (11.04.2024)
The power tool must not be used to grind stone materials
with diamond grinding heads.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Standard auxiliary handle (insulated gripping sur-
a)
face)
(4) Two-pin spanner for clamping nut
(5) Protective guard for grinding
(6) Locking screw for protective guard
(7) Mounting flange with O‑ring
a)
(8) Grinding disc
(9) Disc brush (dia. 22.22 mm)
a)
(10) Disc brush (M14)
(11) Clamping nut
(12) Quick-clamping nut
(13) Protective guard for cutting
a)
(14) Cutting disc
(15) Handle (insulated gripping surface)
(16) Grinding spindle
a)
(17) Diamond cutting disc
(18) Extraction guard for cutting with cutting guides
a)
(19) Hand guard
a)
(20) Rubber sanding pad
a)
(21) Sanding sheet
a)
(22) Round nut
a)
(23) Cup brush
(24) Cover for cutting
a)
(25) Open-ended spanner
a)
(26) Conical brush
a)
(27) Diamond annular cutter
(28) Vibration-damping auxiliary handle (insulated grip-
ping surface)
a) This accessory is not part of the standard scope of delivery.
GWS 27-180 J
3 601 HC4 3..
W
–1
min
mm
mm
a)
a)
a)
a)
GWS 27-230 J
3 601 HC5 3..
2700 2700
8500 6500
180 230
M 14 M 14
25 25
● ●
Bosch Power Tools