Bosch AdvancedSaw 18V-140 Notice Originale page 16

16 | English
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an elec-
tric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it un-
stable and may lead to loss of control.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Ensure that the footplate always rests securely while
u
sawing. A jammed saw blade can break or lead to kick-
back.
When the cut is completed, switch off the power tool
u
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the power tool securely.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side
u
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
Only use the power tool with the base plate. If you do
u
not use the base plate, you are at risk of not being able to
control the power tool.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery in the manufacturer's products.
u
This is the only way in which you can protect the battery
against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
1 609 92A 8M8 | (18.08.2023)
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for making separating cuts and
cut-outs in wood, plastic, metal, ceramic plates, rubber and
laminate/HPL (High Pressure Laminate) while resting firmly
on the workpiece. It is suitable for straight and curved cuts
with mitre/bevel angles of up to 45°. The saw blade recom-
mendations are to be observed.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Lock-off function for on/off switch
(2) On/off switch
(3) Battery Charge Indicator on the Power Tool
a)
(4) Battery release button
a)
(5) Rechargeable battery
(6) Extraction outlet
(7) Sawdust blower device switch
(8) Orbital action adjusting lever
(9) Handle (insulated gripping surface)
(10) Glide shoe
(11) Base plate
a)
(12) Saw blade
(13) Viewing window for Cut Control Cut Control
(14) Shock protection guard
(15) Base for Cut Control Cut Control
(16) Worklight
(17) Saw blade receptacle
(18) SDS lever for saw blade release
(19) Guide roller
(20) Anti-splinter guard
(21) Guide for parallel guide
a)
(22) Extraction hose
a)
(23) Dust extraction adapter
(24) Scale for mitre/bevel angles
(25) Base plate screw
(26) 45° cut mark
(27) 0° cut mark
(28) 45° cut mark with glide shoe
(29) Locking screw for parallel guide
a)
Bosch Power Tools