Hilti HIT-CT 100 Manuel D'utilisation page 9

bereits geöffnetes Foliengebinde aufgeschraubt, die ersten Hübe ebenfalls verwerfen. | In wassergesättigtem Beton ist es
erforderlich, den Anker sofort nach der Bohrlochreinigung zu setzen!
s Nichtbeachtung der Anweisungen kann zum Versagen der Befestigung führen!
[EN Adhesive anchoring system for rebar and anchor fastenings in concrete
Prior to use of product, follow the instructions for use and the safety precautions.
Hilti HIT-CT 100
Contains: dibenzoyl peroxide
Harmful to aquatic life with long lasting effect.
Contains dibenzoyl peroxide. May produce an allergic reaction.
Disposal considerations: Empty packs: Leave the mixer attached and dispose of via the local Green Dot recovery system or
EAK waste material code: 150102 plastic packaging | Full or partially emptied packs: Must be disposed of as special waste in
accordance with official regulations. | EAK waste material code: 20 00 00* MUNICIPAL WASTES (HOUSEHOLD WASTE AND
SIMILAR COMMERCIAL, INDUSTRIAL AND INSTITUTIONAL WASTES) INCLUDING SEPARATELY COLLECTED FRAC-
TIONS. | or european waste catalogue: 08 04 10 waste adhesives and sealants other than those mentioned in 08 04 09. |
Content: 330 ml / 11.1 fl.oz; 500 ml / 16.9 fl.oz | Weight: 600 g / 21.1 oz; 910 g / 32.1 oz
Hilti accepts no liability for damage or failure caused by: Storage and transport not in accordance with the specified
conditions | Failure to observe the instructions for use and setting data | Inadequate design of the anchor points |
Inadequate load bearing capacity of the base material | Incorrect use | Other influences of which Hilti is not aware or on
which Hilti has no influence, e.g. use with products from a third party
Product Information: Always keep these instructions together with the product even when given to other persons. | Check
expiration date: See imprint on foil pack manifold (month/year). Do not use expired product. | Foil pack temperature during
usage: +5 °C to 40 °C / 41 °F to 104 °F. | Base material temperature at time of installation: 0 °C to 40 °C / 23 °F to 104 °F. |
Conditions for transport and storage: Keep in a cool, dry and dark place between +5 °C to 25 °C / 41 °F to 77 °F. | For any
application not covered by this document / beyond values specified, please contact Hilti. | Partly used foil packs must be used
up within 4 weeks. Leave the mixer attached on the foil pack manifold and store under the recommended storage conditions. If
reused, attach a new mixer and discard the initial quantity of anchor adhesive. A new mixer must be used for each new foil
pack.
s WARNING
s Improper handling may cause mortar splashes. We recommend to wear safety glasses, gloves and protective clothes
during installation. | Never start dispensing without a mixer properly screwed on. | Attach a new mixer prior to dispensing a
new foil pack (ensure snug fit). | Use only the type of mixer supplied with the adhesive. Do not modify the mixer in any
way. | Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).
s Poor load values / potential failure of fastening points due to inadequate borehole cleaning. Hilti hollow drill bits TE-CD,
TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity
(volumetric flow rate) as specified in the accessory table. | The boreholes must be free of debris, dust, water, ice, oil, grease
and other contaminants prior to adhesive injection. | For blowing out the borehole - blow out with oil free air untilreturn air
stream is free of noticeable dust. | Important! Remove all water from the borehole and blow out with oil free compressed air
until borehole is completely dried before mortar injection. | For brushing the borehole – only use specified wire brush. The
brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
s Ensure that boreholes are filled from the back of the borehole without forming air voids. If necessary use the accessories /
extensions to reach the back of the borehole. | For overhead applications use the overhead accessories HIT-SZ / IP and
Hilti HIT-CT 100
9